Product Description And Specifications; Product Features; Technical Data; Noise/Vibration Information - Bosch GSH 5 Professional Notice Originale

6 | English
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hammer Safety Warnings
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for chiselling work in concrete,
brick, stone and asphalt, as well as for driving in and com-
pressing with the appropriate accessories.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
1 609 92A 6WC | (07.07.2021)
(1) Dust protection cap
(2) Locking sleeve
(3) Chisel adjustment switch (Vario-Lock)
(4) Lock-on button for on/off switch
(5) On/off switch
(6) Auxiliary handle (insulated gripping surface)
(7) Handle (insulated gripping surface)
(8) Knurled nut for auxiliary handle

Technical Data

Demolition hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to EPTA-Proced-
ure 05:2016
Tool holder
Lubrication
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
107 dB(A). Uncertainty K=3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to
EN 60745-2-6:
2
Chiselling: a = 14 m/s , K = 1,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
GSH 5
3 611 C37 0..
W 1100
-1
min 2850
J 7.5
SDS max
Central permanent
lubrication
kg 5.6
/ II
2
Bosch Power Tools