Product Description And Specifications; Technical Data; Auxiliary Handle - Bosch GSH 500 Professional Notice D'utilisation D'origine

6 | English
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hammer Safety Warnings
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock.
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Always make sure that you maintain a safe distance.
u
When operating the power tool in high up areas, e.g.
on a ladder, ensure that no one is beneath you.
Never touch the application tool or parts of the power
u
tool near to the application tool after use; these may
be extremely hot. There is a risk of burns.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
1 609 92A 484 | (04.04.2018)
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for chiselling work in concrete,
brick, stone and asphalt, as well as for driving in and com-
pressing with the appropriate accessories.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Dust protection cap
(2) Locking sleeve
(3) Lock-on button for on/off switch
(4) On/off switch
(5) Handle (insulated gripping surface)
(6) Auxiliary handle (insulated gripping surface)

Technical Data

Demolition hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to EPTA Proced-
ure 05:2016
Tool holder
Lubrication
Weight according to EPTA
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.

Auxiliary Handle

Do not operate your power tool without the auxiliary
u
handle (6).
You can swivel the auxiliary handle (6) to any angle for a safe
work posture that minimises fatigue.
– Turn the lower gripping end of the auxiliary handle (6) an-
ticlockwise and swivel the auxiliary handle (6) into the re-
quired position. Then, turn the lower gripping end of the
auxiliary handle (6) clockwise to retighten.
GSH 500
3 611 C38 6..
W 1100
rpm 2900
J 7.8
17 mm hex
Grease lubrication
kg 5.6
/ II
Bosch Power Tools