Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Compliance Information
FCC Warning Message
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IC RSS Warning
This device complies with Industry Canada licence-exempt RSS
standard (s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
NCC Warning Message
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號
或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；
經發現有干擾現象時， 應改善至無干擾時方得繼續使用。 前項合法通信，
指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信
或工業、科學及醫療用電波輻射性電機設備之干擾。
KCC Warning Message
" 해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비
스는 할 수 없습니다 ."
" 해당 무선설비는 운용 중 전파혼신 가능성이 있음 "
인증받은자의 상호 : SZ DJI TECHNOLOGY CO., LTD
제품명 / 모델명 : 특정소출력무선기기 ( 무선데이터
통신시스템용무선기기 )/M600P
제 조 자 및 제 조 국 가 : SZ DJI TECHNOLOGY
CO., LTD
제조년월 : 2016.10
인증번호 : MSIP-CRM-dji-M600P
해당 무선설비는 전파혼신 가능 성이 있으므로 인명
안전과 관련된 서비스는 할 수 없음
EU Compliance Statement
SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device
is in compliance with the essential requirements and other relevant
provisions of the R&TTE Directive.
A copy of the EU Declaration of Conformity is available online at
www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industrie Strasse. 12, 97618,
Niederlauer, Germany
Before You Begin
The following documents have been produced to help you safely
operate and make full use of your Matrice 600 Pro:
In the Box
Disclaimer and Safety Guidelines
Quick Start Guide
Intelligent Flight Battery Safety Guidelines
User Manual
Check to see that you have all of the components listed in the In the Box
document. Before assembly, read the Disclaimer and Safety Guidelines.
Then prepare for your first flight by using the Quick Start Guide. For more
information, please refer to the User Manual available on the DJI website.
Make sure you fully understand the functionality of each individual part,
the flight condition requirements, the key contingency warning functions/
systems, and all government regulations before each flight. If you have
any questions or problems during the assembly, maintenance or use of
this product, please contact DJI or a DJI authorized dealer.
Individual Parts
Regarding Genuine and Functional Parts
To avoid component malfunction, serious injury, and property
damage, observe the following rules:
1. Use only genuine DJI parts or parts certified by DJI. Unauthorized
parts or parts from non-DJI certified manufacturers may cause
system malfunctions and compromise safety.
2. Ensure there are no foreign objects (such as water, oil, soil, sand,
etc.) inside of the aircraft or its components.
3. Ensure the aircraft and its components-including but not limited
to the remote controller, flight controller, LIGHTBRIDGE
Air System, landing gear, GPS, compass, propulsion system,
and batteries-are all in good working order, damage-free, and
functioning well. Refer to the remaining sections in this document
for more details on how to ensure the functionality of these
components.
4. DO NOT remove parts that come with the aircraft-including but
not limited to the flight controller, power management unit, and
Lightbridge 2 Air System-for other uses. DO NOT replace any of
them with other parts.
©
TM
2016 DJI All Rights Reserved.
2
5
Publicité
Table des Matières
