Before You Begin; Tools And Parts Needed; Parts Included; General Information - Thermador MASTERPIECE SGS Série Guide D'installation

Before You Begin

Tools and Parts Needed

Phillips Head Screwdriver
▯
Tape Measure
▯
Teflon Tape (Gas Rated)
▯
Drill with 1/4" (6.5mm) bit
▯

Parts Included

Foam Tape
▯
Mounting Brackets (4)
▯
Screws, #10-32 x 2 1/2" (63.8 mm) (4)
▯
Sheet Metal Screws, #8 x 3/8" (9.5 mm) (4)
▯
Washers (4)
▯
Burner Grates (3)
▯
Burners (5)
▯
Burner Caps (5)
▯
Pressure Regulator
▯
LP Gas Conversion Kit
▯
Note: Carefully check all packaging for grates, burners,
caps and regulator. If parts are missing or damaged, call
the number or write to the address listed on the inside
back cover.

General Information

Overall Dimensions
Width (Side to Side)
Depth (Front to Back)
Height (Top to Bottom)
Note: These are overall dimensions NOT cutout
dimensions.

Preparation

Electrical Requirements
CAUTION
9
Do not use an extension cord with the gas cooktop.
This appliance requires a 60 Hz, 15 Amp, 120 VAC
connection. Plan the installation so that the power
connection is accessible from the front of the cabinet.
30" Models 36" Models
31" 37"
(788 mm) (940 mm)
21 1/4" 21 1/4"
(540 mm) (540 mm)
3 13/16" 3 13/16"
(97 mm) (97 mm)
Gas Requirements
Supply Pressure:
Natural Gas: 7 inches water column (14.9 Millibars)
▯
Propane Gas: 11 inches water column (27.4 Millibars)
▯
The propane gas tank must be equipped with its own
high pressure regulator in addition to the pressure
regulator supplied with this unit. The cooktop is shipped
from the factory for use with natural gas. For use with
non pedestal LP conversion kit model SNLPKITW must
be purchased separately. Pedestal cooktops need to
order LP conversion kit model SLPKITPEDW and must
also be purchased separately. A certified technician or
installer must do the conversion.
Cabinet Requirements
Dimension requirements in image below are for
combustible surfaces. When the surface is protected by
a material listed by UL as a Floor Protector and Wall
Shield covered with not less than No. 28 MSG sheet
metal 0.015 inch (0.38mm) stainless steel, 0.024 inch
(0.6mm) aluminum copper, it is considered
noncombustible and some dimensions may be reduced.
For a noncombustible surface over the cooktop, the
minimum clearance is 24" (61cm) rather than 30"
(76cm).
Depth from back wall
Cabinet max. 13" (330)
SGS(X)30 - min. 30" (762)
SGS(X)36 - min. 36" (914)
Above counter - min. 30" (762) to
Combustible surface
min.18" (457)
Centered over cooktop
*Left side
Rear wall - min. 2" (51)
min. 12"
(305)
*Side wall clearance dimensions can be reduced to 5"
(127 mm) if opposing side wall is ≥ 23" (584 mm).
Instructions are based on standard American cabinets
▯
36" high (91cm) x 24" deep (61cm) with a 25"
(63cm) countertop.
The maximum depth of a cabinet installed above the
▯
cooktop is 13" (33cm).
*Right side
min. 12"
(305)
( )=mm
7