Table des Matières
Publicité
Kit Setup - Stand Up
Name:
City:
Track
Tight
Indoor
Outdoor
Open
Conditions
Front Suspension
Toe: ________________________________________________
+/- 0 deg
Ride Height: ______________ Camber: _________________
23mm
Caster:
0º
5º
Kick Angle:
20º
25º
VLA Setting:
Short Arm
Front Pivot:
Alum
Plastic
Kick Shim:
Brass
Plastic
Oil: ________________________________________________
32.5 wt
Piston: _____________________________________________
2 x 1.6mm (TLR233009)
Spring:
Standard
Low Freq. Color: ________________
Sway Bar:
0.8mm
1.0mm
Shock Limiters: _____________ Stroke: _________________
1mm
Shock Locations: ____________________________________
1 - Middle
Spindle Ball Stud:
Standard
1mm
Bump Steer Spacers: _________________________________
Ackerman Ball Stud:
Standard
Ackerman Spacers: __________________________________
1mm
Ackerman Arm:
#1
#2
Axle Spacing:
0
+0.5mm
Trail:
2mm
3mm
4mm
Camber Link: _______________________________________
2 - B
Rear Suspension
Configuration:
Laydown
LD Diff. Height:
Standard
Transmission Type:
3-Gear
Toe Inserts:
0.5
1
1.5
Anti-Squat Inserts:
0
0.5
Inner Roll Center:
LRC
Ride Height: ______________ Camber: _________________
23mm
Rear Hub Spacing: __________________________________
Middle (2mm front, 2mm rear)
Rear Axle Height:
Standard
Hex Width: _________________________________________
Standard
Sway Bar:
1.0mm
1.2mm
Oil: ________________________________________________
32.5 wt
Piston: _____________________________________________
2 x 1.7mm (TLR233010)
Spring:
Standard
Low Freq. Color: ________________
Shock Limiters: _____________ Stroke: _________________
0mm
Shock Locations: ____________________________________
2 - Middle
Shock Mounting:
Front
Inner Link Spacer:
-1mm
Camber Link: _______________________________________
2 (Stand up) - E
6.5" - 1 line wicker
Wing/Wickerbill: ____________________________________
Wing Angle:
0°
2°
4°
Battery Position: ____________________________________
Shorty - Middle
Diff Type:
Ball
Gear Setting: _______________________
Driveshaft Length:
CVA
Chassis
Electronics Plate
Brass, 25g
Servo Plate
Brass, 50g
Brass, 14g
_________
_________
Front Pivot
Brass Pivot, 50g
Brass Kick Shim, 7g
Date:
Track:
State:
Blue Groove
Smooth
Hard Packed
Rough
Loose/Loamy
Dry
-1 deg
30º
Long Arm
HRC
Alum HRC
Silver
1.2mm
______________
22mm
Low Mount
Low Mount
#3
_____________________
+1mm
Standup
+3.5mm
4-Gear
2
2.5
3
3.5
4
1
1.5
2
2.5
3
HRC
-1.5 deg
+3mm
1.4mm
_______________
White
30.5mm
Rear
0mm
+1mm
Normal, 3/4–1 rotation
67mm
Universal Length: __________
Battery Plate
_________
Event:
Grass
Low Bite
Wet
Dusty
Astro Turf
Med Bite
2mm
_______
1mm
_______
SPACER
SPACER
B
A
3mm
_______
SPACER
Notes: ______________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
E
D
D
1
2mm
_______
SPACER
C
B
A
2 Standup
Electronics
Radio: _________________
Servo: _________________
ESC: ___________________
Initial Brake: ___________
Drag Brake: ____________
Throttle Profile: ________
Tires
Anti-Squat Block
Brass, 27g
Aluminum
Tire:
Compound: _________________________
Insert:
Additive:
Notes: _______________________________
_____________________________________
_____________________________________
Rear Ballasts
Brass, 25g
Brass, 50g
High Bite
Other
1
2
3
1
2mm
_______
SPACER
2
LONG
SHORT
INSIDE
MIDDLE
OUTSIDE
2 Laydown
3
3
2
1
0mm
_______
SPACER
OUTSIDE
MIDDLE
INSIDE
Timing Advance: ______________
Throttle/Brake Expo: __________
Servo Expo: ___________________
Throttle/Brake EPA: ___________
Motor: _______________________
78T
Pinion: _________Spur: _________
Battery: ______________________
Front
Rear
__________________________
__________________________
__________________________
73
73
Publicité
Table des Matières
