Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Auxiliary function
Cancel audio warning
Your dryer will give an audio warning when the programme
comes to an end. If you do not want to hear the audio
warning, press "Cancel Audio Warning" button. The
relevant light will turn on when this button is pressed and
an audio warning will not be given when the programme
comes to an end.
C
You can select this function either before or after the
programme starts.
Warning indicators
C
Warning indicators may differ according to the model of
your dryer.
Filter cleaning
A warning light will turn on to remind filter cleaning after
the programme finishes.
C
If the filter cleaning warning light lights up continuously,
please refer to, "Suggested solutions for problems".
Time delay
If you wish to dry your clothes at a later time, thanks to the
time delay function, you can delay the program start up to
3 hours, 6 hours or 9 hours.
1. Open the loading door and put the laundry in.
C
Make sure that all air outlets are open, door filter is
cleaned and the water tank is empty.
2. Set the drying program and, if required, the auxiliary
functions.
3. When the time programming button is pressed once,
a 3 hour delay is selected and the relevant led lights.
When the same button is pressed again, 6 hours; and
if pressed once more, 9 hours delay will be selected.
If the time programming button is pressed one more
time, time delaying function will be cancelled. Set the
time delay as you require.
4. Delayed operation of the selected program is started
by pressing the "Start/Pause/Cancel" button after
selecting the time delay.
C
Additional laundry may be loaded / taken out during the
time delay period.
C
During the time delay period, laundry is rotated for 4
seconds in every 10 minutes to prevent creasing.
Canceling the time delay
If you want to cancel the time delay countdown and start
the program:
1. Press "Start/Pause/Cancel" button for about 3
seconds.
2. Press "Start/Pause/Cancel" button to start the
program right away.
Starting the programme
1. Press "Start/Pause/Cancel" button to start the
programme.
2. Light of the "Start/Pause/Cancel" button will turn on to
indicate that the programme has started.
Progress of program
Progress of a running program is shown through the
program follow-up indicator.
At the beginning of every program step, the relevant
indicator LED will light up and light of the completed step
will turn off.
"Drying":
- Drying level will be illuminated during the whole drying
process until the drying degree reaches "iron dry".
"Iron Dry":
- Starts to illuminate when the drying degree reaches "iron
dry" step and remains illuminated until the next step.
"Ready to wear":
Starts to illuminate when the drying degree reaches "Ready
to wear" step and remains illuminated until the next step.
"Final / Anti-creasing":
- Illuminates when the program comes to an end and anti-
creasing function is activated.
C
If more than one LED light up or flash concurrently, it
means there is malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after it has started
You can use this feature to dry your clothes under higher or
lower temperatures after your dryer has started.
For example;
1. Press and hold the "Start/Pause/Cancel" button for
about 3 seconds to "Cancel" the programme in order
to select "Extra Dry" programme instead of "Iron Dry"
programme.
2. Select the "Extra Dry" programme by rotating the
programme selection button.
3. Press "Start/Pause/Cancel" button to start the
programme.
C
Press "Start/Pause/Cancel" button for 3 seconds
to cancel the programme or turn the programme
selection knob in any direction to end the programme
while the machine is running. Water tank and filter
cleaning warning lights turn on to warn the user when
the programme is cancelled by pressing the "Start/
Pause/Cancel" button for 3 seconds. However, the
warning lights do not turn on when the programme
is cancelled by turning the programme selection
knob. Only the drying light turns on and the machine
remains in hold until a new programme is selected
and the "Start/Pause/Cancel" button is pressed. Child-
proof lock of the machine should not be active in order
to perform these two operations. If the child-proof
lock is active, deactivate it before performing these
operations.
Adding/removing laundry in standby mode
In order to add or remove laundry after the programme
starts:
1. Press the "Start/Pause/Cancel" button to switch the
dryer to "Pause" mode. Drying process will stop.
2. Open the door at "Pause" position and close it again
after adding or taking out laundry.
3. Press "Start/Pause/Cancel" button to start the
programme.
C
Any laundry added after the drying process has
started may cause the dried clothes in the machine
intermingle with wet clothes and the result will be wet
laundry after the drying process is over.
12 EN
Publicité
Table des Matières
