Manual Operation (Cool, Dry, Fan); Air Flow Velocity And Direction Adjustment - Mitsubishi Electric MCF-GA35VB Mode D'emploi

MANUAL OPERATION (COOL, DRY, FAN)

1
To select the "COOL", "DRY" or "FAN" mode:
Press the
2
˚C
CLOCK
AMPM Select the operation mode by pressing the
Each time this button is pressed, the operation mode is changed in sequence :
(I FEEL...) →
TOO TOO
ON/OFF
WARM COOL
To stop operation:
I
Press the
FAN STOP
I FEEL COOL
After the operation mode is set once, the operation starts in the mode set previ-
VANE START
ously from the next time by simply pressing the
FAN DRY
MODE HR.
ECONO COOL MIN.
RESET CLOCK
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
I
When the set temperature is to be changed:
TOO
WARM
• Press the button to lower the temperature.
One press lowers the temperature by about 1°C.
TOO
COOL
• Press the button to raise the temperature.
One press raises the temperature by about 1°C.
In "DRY" operation
• The temperature control (temperature setting) cannot be done.
• The room temperature is slightly lowered in this operation mode.
I
The details of the display on the indoor unit are explained on page 6.
Note:
When the ambient temperature is too high, the room temperature may not reach the set temperature since
the unit operates to cool under high load.
Description of "AUTO RESTART FUNCTION"
• Refer to page 6.
ON/OFF
button.
MODE
button.
(COOL) → (DRY) →
(FAN)
ON/OFF
button.
ON/OFF button.

AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT

AIR FLOW velocity and direction can be selected as required.
I
To change the AIR FLOW velocity, press the
Each time the button is pressed, the fan speed is changed in sequence:
(Lo) →
˚C
CLOCK
AMPM
• Use the
12345
• If the operating sound of the air conditioner disturbs your sleep, use the
(Lo) notch.
TOO TOO
ON/OFF
I
WARM COOL
To change the AIR FLOW blowing direction vertically, press the
VANE
button.
Each time the button is pressed, the angle of the horizontal vane is changed in
sequence : 1 → 2 → 3 → 4 → 5 →
FAN STOP
I FEEL COOL
VANE START
SWING OPERATION
FAN DRY
Use the swing operation for the air flow to reach all corners of the room.
MODE HR.
ECONO COOL MIN.
Recommended horizontal vane range
RESET CLOCK
Use the
Use position 1 or 2 in the COOL or DRY mode when
adjusting to your requirements.
Notes:
• In the cooling operation, when the air conditioner is operated with setting the horizontal vane to 4 or 5 for 1 hour, the
AIR FLOW direction is automatically set to position 1 to prevent condensed water from dropping.
• Adjust the vertical AIR FLOW direction using the remote controller. If the horizontal vane is moved manually, it
may cause trouble.
I
To change the horizontal direction of the AIR FLOW
For the floor standing unit
• Change the direction of the vertical vane manually.
Adjust the vane before operation starts.
Since the horizontal vane moves automatically, your fingers may be caught.
AUTO AIR FLOW DIRECTION CONTROL OPERATION
VANE
• When the AUTO mode is selected with the
correspond to the operation mode for effective operation.
For the floor standing unit
(1) COOL, DRY
• The air is blown out upwards.
(2) FAN
• The air is blown out horizontally.
FAN
(Med) → (Hi) →
(AUTO)
(Hi) notch to cool the room more.
(SWING) →
(AUTO)
(AUTO) position usually.
For the ceiling suspended unit
• Change the direction of the vertical vane manually.
button, the position of the horizontal vane is automatically set to
For the ceiling suspended unit
(1) COOL, DRY
• The air is blown out horizontally.
(2) FAN
• The air is blown out downwards.
button.
1
2
3
4
5
7