Additional Safety And Working Instructions - Würth H 28-MLE Power Traduction Des Instructions De Service D'origine

OBJ_BUCH-1999-001.book Page 11 Friday, June 7, 2013 11:39 AM
 Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
 Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preven-
tive safety measures reduce the risk of starting the power
tool accidentally.
 Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
 Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
 Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
 Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could result in
a hazardous situation.
Service
 Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool is
maintained.
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause
hearing loss.
 Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
 Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory or fastener may contact
hidden wiring. Cutting accessory and fasteners con-
tacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual cur-
rent device (RCD) with a rated residual current of 30 mA or
less.
Additional Safety and Working
Instructions
 Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be
operated with 220 V.
 Use appropriate detectors to determine if util-
ity lines are hidden in the work area or call the
local utility company for assistance. Contact with
electric lines can lead to fire and electric shock. Damaging
a gas line can lead to explosion. Penetrating a water line
causes property damage.
 Firmly tighten the auxiliary handle, hold the
machine firmly with both hands while working
and keep proper footing and balance at all
times. The machine is securely guided with both hands.
 Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
 To save energy, only switch the power tool on when using
it.
 For drilling without impact in wood, metal, ceramic and
plastic as well as for screwdriving, tools without SDS-plus
are used (e.g., drills with cylindrical shank). For these
tools, a keyless chuck or a key type drill chuck are
required.
 H 28-MLS Power: Only use quick change chucks with
3 identification grooves (standard delivery scope)
or 2 identification grooves (accessory/spare part)
– see figure 1, page 175.
 The quick change chuck is automatically locked. Check
the locking effect by pulling the quick change chuck.
 Inserting SDS-plus Drilling Tools: Check the latch-
ing by pulling the tool.
11