Table des Matières
Publicité
ES
Toma IEC con portafusibles integrado. Para enchufar el cable suministrado con conector IEC. NOTA IMPORTANTE: Sustituya el fusible
únicamente por otro del mismo tipo y características. Si el fusible se fundiera continuamente, póngase en contacto con un servicio técnico
autorizado.
PL
Gniazdo sieciowe IEC ze zintegrowaną podstawą bezpiecznika. Podłączanie przy użyciu kabla sieciowego IEC dostarczanego wraz z głośnikiem.
WAŻNA INFORMACJA: bezpiecznik należy wymieniać wyłącznie na bezpiecznik tego samego typu i o takich samych parametrach. Jeśli bezpiecznik
stale się przepala, należy skontaktować się z autoryzowanym centrum serwisowym.
IT
Presa di rete CEI con portafusibili integrato. Collegamento tramite il cavo di alimentazione CEI incluso nella fornitura. NOTA IMPORTANTE:
sostituire il fusibile solo con un fusibile dello stesso tipo e con gli stessi valori. Se il fusibile continua a saltare, rivolgersi a un centro di assistenza
autorizzato.
OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
When the spotlight is properly connected to the mains, the motors are reset. Within a few seconds, the spotlight is ready for use and changes to
the mode that was previously selected.
A. SETTING DMX START ADDRESS
Press the MODE button repeatedly until the LED indicator shows either "Addr" (if no DMX signal is present), or the DMX start address (as soon as a
DMX signal is present, A001 - A512). Press ENTER in both cases, and while all four characters are flashing on the display, the DMX start address can
be set as desired using the UP and DOWN buttons. To confirm, press ENTER. The synchronous control of multiple spotlights (same model) through
a DMX control unit (e.g. DMX mixer) can be achieved by assigning the spotlights to an identical DMX start address and DMX mode and connecting
them using DMX cables.
B. SETTING DMX MODE
Press the MODE button repeatedly until "ChMO" appears on the display. Press ENTER, and while all four characters are flashing on the display, the
DMX start address can be set as desired using the UP and DOWN buttons. To confirm, press ENTER.
C. SLAVE MODE
Press the MODE button repeatedly until "SLA" appears on the display. Press the ENTER button and select one of the four different slave modes using
the UP and DOWN buttons and confirm with ENTER. Connect the slave and the master unit (same model) with a DMX cable and activate one of the
standalone modes on the master unit. Now the slave unit follows the master unit according to the setting.
SLA
SL 1
No reversal of the PAN and TILT direction
SL 2
Reversal of the PAN direction
SL 3
Reversal of the TILT direction
SL 4
Reversal of the PAN and TILT direction
D. AUTOMATIC CONTROL
Press the MODE button repeatedly until "AUTO" appears on the display. The AUTO mode starts immediately. Press ENTER. The display now shows
one of the 17 auto programs (PR00 - PR16). To activate one of the other auto programs, press ENTER again. While all four characters are flashing on
the display, one of the programs can be selected using the UP and DOWN buttons. Confirm the input with ENTER. Using the UP and DOWN buttons,
you can now change the speed of the program by selecting " SPxx " (Speed). Then press ENTER and use the UP and DOWN buttons to select the
desired speed ranging from "SP00" to "SP99" (SP00 = minimum speed; SP99 = maximum speed). Confirm the input with ENTER.
E. MUSIC CONTROL
Press the MODE button repeatedly until "SoUn" appears on the display. The Music control mode starts immediately. Press ENTER. The display now
shows one of the 17 auto programs in the Music control mode (PR00 - PR16). To activate one of the other auto programs, press ENTER again. While
all four characters are flashing on the display, one of the programs can be selected using the UP and DOWN buttons. Confirm the input with ENTER.
Using the UP and DOWN buttons, you can now display the menu item "SUxx" to adjust the sensitivity with which programs respond to music signals
(bass pulses). Then press ENTER and use the UP and DOWN buttons to select the desired microphone sensitivity ranging from "SU00" to "SU99"
(SU00 = minimum sensitivity; SU99 = maximum sensitivity). Confirm the input with ENTER.
13
Publicité
Table des Matières
