Memory Storing The Radio Code Page; Memory Storage Of Ds Radio Controls; Memory Storage Of Slh Radio Controls; Memory Storage Of Rc/Lc Radio Controls (For Some Markets Only) - FAAC E012S Mode D'emploi

8 MEMORY STORING THE RADIO CODE
The control board has an integrated 2-channel decoding
system (DS, SLH, RC, LC) named OMNIDEC. This system
makes it possible to memory-store both total opening
(OPEN A) and partial opening OPEN B) of the automated
system - this is made possible by an additional receiver
module (fig.3 ref. ) and radio controls on the same
frequency.
The 3 types of radio codes (DS, LSH, RC, LC)
cannot coexist.
Only one radio code can be used at a time.
To change over from one code to another, you
must delete the existing one (see paragraph
on deletion), and repeat the memory-storage
procedure.
8.1 MEMORY STORAGE OF DS RADIO
CONTROLS
A maximum of two codes can be stored. One
on the OPEN A channel and one on the OPEN
B channel.
1. On the DS radio control, select the required ON-OFF
combination for the 12 dip-switches.
2. Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or
partial opening (OPEN B), and as you hold it down,
also press the SETUP (SW1) push-button. The relevant
LED starts to flash slowly for 5 sec..
3. Release both push-buttons.
4. Within these 5 sec., press the appropriate push-button
on the radio control.
The relevant LED lights up on steady beam for 1
5.
second and then goes OFF, indicating that storage
was executed.
6. To add other radio controls, set the same ON - OFF
combination used in point 1.
8.2 MEMORY STORAGE OF SLH RADIO
CONTROLS
A maximum of 250 codes can be memory stored,
split between OPEN A and OPEN B.
1. On the SLH radio control, simultaneously press and
hold down push-buttons P1 and P2.
2. The radio control LED begins to flash.
3. Release both push-buttons.
4. Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or
partial opening (OPEN B), and as you hold it down,
also press the SETUP (SW1) push-button. The relevant
LED starts to flash slowly for 5 sec.
5. Release both push-buttons.
6. Within these 5 sec., while the radio control LED is still
flashing, press and hold down the required push-but-
ton on the radio control (the radio control LED lights
up on steady beam).
7. The LED on the board lights up on steady beam for 1
second and then goes OFF, indicating that storage
was executed.
8. Release the radio control push-button.
9. Quickly press twice the memory stored radio control
push-button.
The automated system performs one opening
operation. Make sure that the automated system
is free of any obstacle created by persons or
things.
To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to the
relevant push-button of the radio controls to be added,
observing the following procedure.
• On the memory stored radio control, simultaneously
press and hold down push-buttons P1 and P2.
• The radio control LED begins to flash.
• Release both push-buttons.
Press the memory stored push-button and hold it down
•
(the radio control LED lights up on steady beam).
• Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing
it only after the double flash of the radio control LED,
which indicates memory storage executed.
• Quickly press twice the push-button of the memory
stored radio control.
The automated system performs one opening
operation. Make sure that the automated system
is free of any obstacle created by persons or
things.
Fig. 3 Fig. 3
8.3 MEMORY STORAGE OF RC/LC RADIO
CONTROLS (for some markets only)
A maximum of 250 codes can be memory stored,
split between OPEN A and OPEN B.
1. Use RC/LC remote controls only with receiver module
at 433 MHz.
2. Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or
partial opening (OPEN B), and as you hold it down,
also press the SETUP (SW1) push-button. The relevant
LED starts to flash slowly for 5 sec.
3. Release both push-buttons. Within these 5 sec., press
the appropriate push-button on the RC/LC remote
control.
4. The LED lights up on steady beam for 1 second, indi-
cating memory storage executed, and then resumes
flashing for another 5 sec., during which another radio
control (point 4) can be memory stored.
5. When the 5 sec. have elapsed, the LED goes OFF
indicating the end of the procedure.
6. To add other radio controls, repeat the operation
at point 1.
8.3.1 REMOTE MEMORY STORAGE OF RC/LC
RADIO CONTROLS
1. Other radio controls can be remotely stored only with
the RC/LC radio controls, i.e. without using the LOGIC-
SPEED-SETUP push-buttons, but using a previously
stored radio control.
2. Get a radio control already stored on one of the 2
channels (OPEN A or OPEN B ).
3. Press and hold down push-buttons P1 and P2 simulta-
neously until both the LEDs flash slowly for 5 sec.
4. Within 5 sec. press the push-button of the radio control
that had been memory stored to enable learning on
14