Publicité
Les langues disponibles
Les langues disponibles
Installation Instructions Ergon GA1 Grips
Attention: Please read these instructions carefully. Only correctly installed Ergon grips allow for optimum function. Ergon GA1 grips require a handlebar with 139 mm (size small) or 145
!
mm (size large) of straight uninterrupted bar space each side. Only handlebars with a diameter of 22.2 mm in the grip area may be used. Only handlebars that have been approved by their
manufacturer for use with clamp on grips should be used and can withstand the required clamping force. Carbon bar use permitted. Thin wall handlebars (some carbon and aluminium models)
can be used. Please ensure prior to fitting that the bar is suitably cleaned using alcohol or other degreasers. These grips are not designed to be used with twist shifters.
1.
Please be aware that the grips are left and right
specific. They can be identified from the "left"
and "right" marking as indicated.
3.1
As a guide the grips are marked for orientation. Rotate from this point as desired. Ensure that you
do not restrict the use of the braking and gearing system on the bicycle.
4.
Important:
Recommended torque: 4 Nm
The grips should not turn on the bar!
Re-check the torque setting following the first ride /
50 km of riding. Check periodically to ensure that the
screws are not loosening.
Tighten to 4 Nm torque using a 3 mm torque wrench. Re-check the torque setting following the
first ride / 50 km of riding. Check periodically to ensure that the screws are not loosening.
!
Attention:
Before riding the bike, please ensure that the grips are properly tightened. If the quoted 4 Nm torque is not sufficient to prevent the grips being turned by hand then the handlebar is not compatible with
this product. Please replace the handlebar with one which is completely round at the end and meets the industry standard of 22.2 mm in diameter. Do not over-tighten. To prevent corrosion, the clamp
has a protective coating. Should this coating become damaged, from a crash for example, it is advisable to renew this layer using a paint pen or similar. Following any accidents, all components of the
grips and clamps should be checked for damage and replaced as necessary. Should you have any questions, please refer to your retailer. Before riding for the first time, ensure that the function of the
brakes and gears has not been restricted without having to change your hand position and that all functions of the bicycle can be used as normal. A secure fit can only be guarantied with the use of the
correct Ergon clamp.
Maintenance:
In order to ensure that your Ergon grips provide you with the best performance please clean them regularly using warm soapy water. Rinse thoroughly. Do not use petroleum based products or solvents,
oil or grease on the grips for any reason. All Ergon grips are latex free.
Warranty:
The clamping system used on these grips exceeds the DIN standard 14766 for handlegrips of 70 N removal force. The function and construction of Ergon handlebar grips are covered by a warranty for
two years from the date of purchase. Please be aware that grips do naturally wear out with use. In the event of a suspected warranty issue, please contact your retailer. Damage as a result of crashes,
misuse, incorrect installation or modification of the grip is not covered by this warranty.
2.1
2.2
Ensure that the clamp is firmly
Slide the grip onto the handlebar.
pushed onto the grip.
2.3
Ensure that the grip is fully
inserted onto the bar so that the
clamp is flush with the end of
the bar.
3.2
The default position for the clamp is with the screw facing backwards. It can be independently
positioned as preferred.
5.
Important:
Check List!
Please ensure that you have the correct grips mounted left and right (1). The end of the clamp
should be flush with the end of the bar (2.3). Insert the end plugs as shown.
( GB / US )
2.4
Tighten the clamp using the
backward facing screws.
Publicité
