Getting Started; How To Use - Remington PG400 Mode D'emploi

ENGLISH

GETTING STARTED

CHARGING YOUR PERSONAL GROOMER
Before using your personal groomer for the first time, charge for 14-16 hours.
Ensure the product is switched off.
Place your personal groomer into the charging stand, connect the charging adaptor to the
product and then to the mains. The charging indicator will light up.
Your personal groomer cannot be overcharged. However, if the product is not going to be
used for an extended period time (2-3 months), unplug it from the mains and store. Fully
recharge your personal groomer when you would like to use it again.
To preserve the life of your batteries, let them run out every six months then recharge for
14-16 hours.
CORDED USE
Connect the charging adaptor to the product and then to the mains.
CAUTION: Extended mains only use will result in the reduction of the battery life.

HOW TO USE

BEFORE YOU BEGIN
Always comb your beard or moustache with a fine comb before you start trimming.
REVERSIBLE GUIDE COMBS
These attachment reversible guide combs are for use with the 30mm trimmer blade only.
To attach, gently slide the comb over the trimmer blade. An arrow on the side of the comb
indicates the length which the hair will be cut.
Settings
No guide combs
Small comb
Large comb
Replacement combs available: SP256
2
080189_REM_IFU_PG400_18L.indd GB_2-GB_3 080189_REM_IFU_PG400_18L.indd GB_2-GB_3
mm
0,5 mm
3mm/6mm
9mm/12mm
ENGLISH
ATTACHING AND REMOVING THE GUIDE COMBS
With the trimmer blade facing away from you, slide the guide comb on top of the clipper
blade and click into position.
With the trimmer blade facing away from you, carefully push the guide comb away from
the trimmer blade.
TO THIN AND TAPER THE BEARD/MOUSTACHE (Diagram 1)
Attach a guide comb to the 30mm Trimmer Blade. If you are trimming for the first time
start with the maximum trimming length setting.
Turn the unit on.
Place the flat top of the trimmer comb against the skin.
Slowly slide the personal groomer through the hair. Repeat from different directions as
necessary.
If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull
off the comb and brush/rinse off.
TO DEFINE THE BEARD/MOUSTACHE LINE (Diagram 2)
Hold the personal groomer with 20mm Trimmer Blade facing you.
Start with edge of beard/moustache line and gently lower the trimmer blade onto your
skin. Use motions towards edge of beard/moustache line to trim to desired locations in
facial area and away from beard in neck area.
TRIMMING EDGE OF SIDEBURNS (Diagram 3)
Hold the personal groomer with 20mm Trimmer Blade facing you.
Start with edge of sideburn, and with the trimmer blades resting lightly against your skin,
use motions towards edge of sideburn line to trim to desired locations in facial area.
USING THE MINISCREEN SHAVER (Diagram 4)
Attach the MiniScreen shaver
Hold the groomer so the MiniScreen gently touches your face in a 45 degree angle.
Use short, well-controlled movements to shave around your Beard/Moustache. Use your
free hand to stretch your skin. This encourages the hair to stand upright, making it easier
to shave.
NOTE: The MiniScreen shaver was designed to shave the detail areas around your beard/
moustache/sideburns. It was not designed to shave your entire face. For a close comfortable
®
shave, guaranteed, use one of Remington 's electric shavers.
TRIMMING THE NAPE OF YOUR NECK (Diagram 5)
Note: You will need a hand mirror for this operation if performing it alone.
Before you begin, attach the 30mm Trimmer Blade.
Use your fingers to lift the hair at the base of your head up off the neck. Your index finger
should be covering the roots of the hairs you are lifting to prevent accidental removal by
the personal groomer.
Using your other hand, hold the personal groomer to the base of your neck with the
cutting unit facing up, and move the personal groomer up the length of the neck until it
touches your finger covering the hair roots at the base of your head.
3
10.04.2008 23:12:14 Uhr 10.04.2008 23:12:14 Uhr