Other Information; Wake On; Wireless Display - Durabase DL32F249S4CW-W Mode D'emploi

• The Wireless feature of the TV supports 802.11 a,b,g
• You must change your modem's SSID when there are
Open the Network/Internet Settings menu and select
Network Type as Wireless Device to start connection
process.
the OK button on the remote control.
disconnect from a wireless network, highlight Network
Type and press Left or Right buttons to set as
Highlight Internet Speed Test and press the OK button
Advanced Settings and press the OK button to open
buttons to set. Press the OK button to save settings
when complete.
Connected or Not Connected and the current IP
• If your mobile device has WiFi feature, you can connect
• Connect to your router following the steps stated above
• Afterwards, engage your mobile device with the router and
• If the connection is established correctly, you will be
via the Media Browser of your TV.
Note: If the modem supports N mode, you should set N
mode settings.
& n type modems. It is highly recommended that you
should use the IEEE 802.11n communication protocol
in order to avoid any possible problems while watching
videos.
any other modems around with the same SSID. You
can encounter connection problems otherwise. Use a
wired connection if you experience problems with a
wireless connection.
Configuring Wireless Device Settings
The TV will scan the wireless networks automatically.
A list of available networks will be displayed. Please
select your desired network from the list.
If the selected network is protected with a password,
please enter the correct key by using the virtual keyboard.
You can use this keyboard via the directional buttons and
Wait until the IP address is shown on the screen.
This means that the connection is now established. To
Disabled.
to check your internet connection speed. Highlight
the advanced setting menu. Use directional and numeric

Other Information

The status of the connection will be displayed as
address, if a connection is established.
Connecting to your mobile device via WiFi
it to your TV via a router, in order to access the content
in your device. For this, your mobile device must have
an appropriate sharing software.
in the Wireless Connectivity section.
then activate the sharing software on your mobile device.
Then, select files that you want to share with your TV.
able to access the shared files from your mobile device
Using with mobile devices
• Enter the Media Browser menu and the playback
mobile device and press the OK button to continue.
• If available, you can download a virtual remote
controller application from the server of your mobile
device application provider.

Wake ON

Wake-on-LAN (WoL) and Wake-on-Wireless LAN
(WoWLAN) are standards that allow a device to be
turned on or woken up by a network message. The
message is sent to the device by a program executed
on a remote device connected to the same local area
network, such as a smartphone.
Your TV is WoL and WoWLAN compatible. To enable
this feature set the Wake On option in the Network/
Internet Settings menu as On. It is necessary that
both the device, from which the network message will
be sent to the TV, and the TV are connected to the
same network. Wake On feature is only supported for
Android OS devices and can only be used via YouTube
In order to use this feature the TV and the remote
device should be connected at least once while the TV
reestablished, the next time it is switched on. Otherwise
this feature will be unavailable. This does not apply,
when the TV is switched into the standby mode.
The performance of some devices in the market, may
vary due to the software architecture. In order to use
Wake On feature with a better performance, please

Wireless Display

Wireless Display is a standard for streaming video and
sound content by Wi-Fi Alliance. This feature provides
the ability to use your TV as wireless display device.
screens including graphical, video and audio content
between your mobile device and TV.
doesn't have internal WiFi feature.
Then press the Source button on the remote and
switch to Wireless Display source.
A screen appears stating that the TV is ready for
connection.
Open the sharing application on your mobile device.
brand, please refer to the instruction manual of your
mobile device for detailed information.
Scan for devices. After you select your TV and connect,
the screen of your device will be displayed on your TV.
English - 60 -
Note: This feature may not be supported on all mobile
devices.
device selection OSD will be displayed. Select your
and Netflix applications.
is on. If the TV is powered off, the connection should be
make sure that your device has latest firmware version.
There are different standards which enable sharing of
Plug the wireless USB dongle to TV first, if the TV
These applications are named differently for each