Troubleshooting & Tips; Teletext Services; Software Upgrade - Durabase DL32F249S4CW-W Mode D'emploi

Now/Next Schedule
Event Options
Next/Prev Day (Programme +/- buttons): Displays
the events of previous or next day.
Event Details (Info button): Displays detailed
information about selected events.
Filter (Text button): Views filtering options.
Next Time Slice (Green button): Displays the events
of next time slice.
Options (OK button): Displays event options.
Rec./Stop (Record button): The TV will start to record
the selected event. You can press again to stop the
recording.
Options (OK button): Displays event options.
Event Details (Info button): Displays detailed
information about selected events.
Filter (Blue button): Views filtering options.
Rec./Stop (Record button): The TV will start to
record the selected events. You can press again to
stop the recording.
Use the directional buttons to highlight an event and
press OK button to display Event Options menu. The
following options are available.
Select Channel: Using this option, you can switch to
the selected channel.
Record / Delete Rec. Timer: Select the Record
option and press the OK button. If the event is going
to be broadcasted at a future time, it will be added
to Timers list to be recorded. If the selected event is
being broadcasted at the moment, recording will start
immediately.
To cancel an already set recording, highlight that event
and press the OK button and select the option Delete
Rec. Timer. The recording will be cancelled.
Set Timer on Event / Delete Timer on Event: After
you have selected an event in the EPG menu, press the
OK button. Select Set Timer on Event option and press
the OK button. You can set a timer for future events.
To cancel an already set timer, highlight that event and
press the OK button. Then select Delete Timer on Event
option. The timer will be cancelled.
IMPORTANT: Connect a USB disk to your TV while the TV
the recording feature.
Note: Switching to a different broadcast or source is not
available during a recording.
IMPORTANT: Connect a USB disk to your TV while the TV
the recording feature.
Note: Switching to a different broadcast or source is not
available during a recording.
Notes: You cannot switch to any other channel or source while
there is an active recording or timer on the current channel.
individual events at the same time interval.
is switched off. You should then switch on the TV to enable
is switched off. You should then switch on the TV to enable
It is not possible to set timer or record timer for two or more
3 AM search and upgrade mode
Software upgrade search via user interface
Tv will not turn on
Poor picture
No picture

Teletext Services

Press the Text button to enter. Press again to activate
mix mode, which allows you to see the teletext page
and the TV broadcast at the same time. Press once
more to exit. If available, sections in the teletext pages
will become colour-coded and can be selected by
pressing the coloured buttons. Follow the instructions
displayed on the screen.

Software Upgrade

automatically via the broadcast signal or via Internet.
On the main menu select System>Settings and then
More. Navigate to Software upgrade and press the
OK button. In Upgrade options menu select Scan
for upgrade and press OK button to check for a new
software upgrade.
If a new upgrade is found, it starts to download
the upgrade. After the download is completed
confirm the question asking about rebooting the
TV by pressing the OK to continue with the reboot
operation.
Your TV will search for new upgrades at 3:00 o'clock if
Automatic scanning option in the Upgrade options
menu is set to Enabled and if the TV is connected
to an aerial signal or to Internet. If a new software is
found and downloaded successfully, it will be installed
at the next power on.
Troubleshooting & Tips
Make sure the power cord is plugged in securely to
wall outlet. Check if batteries are exhausted. Press the
Power button on the TV.
• Check if you have selected the correct TV system.
• Low signal level can cause picture distortion. Please
check antenna access.
• Check if you have entered the correct channel
frequency if you have done manual tuning.
• The picture quality may degrade when two devices
are connected to the TV at the same time. In such a
case, disconnect one of the devices.
• This means your TV is not receiving any transmission.
Make sure the correct source has been selected.
• Is the antenna connected properly?
English - 53 -
unplug, wait for two minutes then plug it back in.
Your TV is capable of finding and updating the firmware
Note: Do not unplug the power cord while led is blinking during
the reboot process. If the TV fails to come on after the upgrade,