Technical Specification - Hällde VCM-41 Mode D'emploi

• Do not use abrasive detergents or cleaning
products.
• Avoid the use of cleaning sponges with
scouring pads (e.g. Scotch-Brite™).
ADVICE ON CARE:
• Clean the machine immediately after use.
• Dry the machine immediately after cleaning.
TROUBLE SHOOTING
To eliminate the risk of damage to the motor,
the VCM-41/42 is fitted with thermal motor
protection that automatically switches off the
machine if the temperature of the motor should
become too high. The thermal motor protection
has automatic reset, which means that the
machine can be started again when the motor
has cooled down, which usually takes between
10 and 30 minutes.
FAULT: The machine cannot be started,
or stops while in operation and cannot be
restarted.
REMEDY: Check that the plug is securely fitted
into the power supply socket or turn on the
mains switch. Fit the bowl and lid correctly.
Move the safety arm all the way over the
centre of the lid. Check that the fuses in the
fuse box for the premises have not blown and
that they have the correct rating. Wait for a
few minutes and try to restart the machine. If
the machine still fails to run, call in a qualified
service mechanic.
FAULT: Low capacity or poor cutting results.
REMEDY: Make sure that the blades are in
good condition and are sharp. Cut the food to
be processed into smaller pieces of equal size.
Process the food for a shorter or longer time.
Process smaller quantities at a time. Always
have the scraper fitted and use it whenever
necessary.

TECHNICAL SPECIFICATION

HALLDE VCM - 41
CAPACITY AND VOLUME: Gross volume
4 litres. Net volume liquid 1.6 litres.
MACHINE BASE: Motor: 0.55 kW, 100 V,
single phase, 50/60 Hz, 9/8 A. Motor: 0.55 kW,
110-120 V, single phase, 50/60 Hz, 8 A. Motor:
0.55 kW, 230 V, single phase, 50/60 Hz, 4.7 A.
Thermal motor protection. Transmission: direct
drive. Safety system: three individual safety
switches and mechanical motor brake. Degree
of protection: IP44. Plug: 10 A, earthed. Fuse
in fuse box for the premises: 10 A, delayed.
Sound level LpA (EN31201): 72 dBA. Magnetic
field: less than 0.1 microtesla.
CONTROLS AND SPEEDS: "0" = machine
switched off. "I" = machine runs continuously
at 1 500 rpm (50 Hz) or 1 700 rpm (60 Hz). "P"
(pulse) = machine runs at 1 500 rpm (50 Hz)
or 1700 rpm (60 Hz) until the knob is released.
BOWL VOLUME: Gross volume 4 liters. Net
volume liquid 1.6 liters.
4
NET WEIGHTS: Machine base: 14.8 kg.
Bowl complete with knife, lid and scraper
system: 1.6 kg.
KNIFE: The diameter of the chopping knife
is 190 mm.
NORMS/STANDARDS: NSF STANDARD 8,
see declaration of conformity.
TECHNICAL SPECIFICATION
HALLDE VCM - 42
CAPACITY AND VOLUME: Gross volume 4
litres. Net volume liquid 1.6 litres.
MACHINE BASE: Motor: 0.75 kW, 230 V, three
phase, 50 Hz, 2.5/2.0 A. Motor: 0.75/0.37 kW,
400 V, three phase, 50 Hz, 1.7/1.4 A. Thermal
motor protection. Transmission: direct drive.
Safety system: three individual safety switches
and mechanical motor brake. Degree of protec-
tion: IP44. Plug: 16 A, earthed. Fuse in the fuse
box for the premises: 10 A, delayed . Sound
level LpA (EN31201): 72 dBA. Magnetic field:
less than 0.1 microtesla.
CONTROLS AND SPEEDS: "0" = machine
switched off. "I" = machine runs continuously
at 1 500 rpm. "II" = machine runs continuously
at 3 000 rpm. "P" (Pulse) = machine runs at
1 500 rpm until the knob is released.
NET WEIGHTS: Machine base: 15.4 kg.
Bowl complete with knife, lid and scraper
system: 1.6 kg.
KNIFE: The diameter of the chopping knife
is 190 mm.
NORMS/STANDARDS: NSF STANDARD 8,
see declaration of conformity.
HALLDE • User Instructions