Installation Of The Insertion - Monacor PA-1200C Notice De Montage Et D'utilisation

used for other purposes than originally intended,
if it is not correctly connected or operated, or if
it is not repaired in an expert way .
If the insertion is to be put out of oper-
ation definitively, take it to a local recy-
cling plant for a disposal which is not
harmful to the environment .

4 Installation of the Insertion

WARNING Prior to the installation of the in-
sertion, disconnect the mains plug
of the amplifier or basic unit of the
insertion . Otherwise, there will be an
electric shock hazard .
1) Remove the housing cover of the amplifier or
basic unit .
2) Screw off the cover panel for the insertion com-
partment on the front side of the amplifier or
basic unit . Place the insertion into the compart-
ment and fasten it with screws .
3) Put the loose three-pole line of the amplifier or
basic unit into the pin housing of position CON
1 (x) (see page 3, fig . 2) .
4) Remove the cover plate on the rear side of the
amplifier or the basic unit . Screw the supplied
connection PCB (z) from the outside to this
position on the rear side of the unit . Insert the
supplied ribbon cable into the pin housing CON 3
of the connection PCB (z) and into the pin hous-
ing CON4 (w) of the insertion .
Connect the plug of the three-pole cable of
the DCF receiver (y) to the pin housing (u) . The
radio clock receiver is situated in the sealed hous-
ing . Place this receiver in such a way that a clear
reception of the radio signals will be ensured:
Important! Never place the DCF receiver in a
metallic housing (e . g . in a rack) . The reception
of the radio signal may also be impaired by inter-
ference, such as magnetic fields (transformers,
computers, power cables, etc .) . In this case, the
receiver must be placed differently . It may take
a few minutes until the timer takes over the
current time .
If no time signal or no clear time signal is
received for a longer period, the message NO
12
a
1
c
d
b
2 3
CHIME A CHIME B CHIME C
UP DOWN ENTER
e
SIGNAL is displayed alternately with the date
and the time . As soon as the reception is clear
again or the reception module is placed in an
optimum way, the radio module will automat-
ically update the time setting .
5) The relay contacts are switching contacts and can
be charged with ⎓ 24 V/ 500 mA as a maximum .
Connect the contacts REL 1 to REL 3 to the units
to be controlled .
The connections CHIME A, CHIME B, and
CHIME C are connected in parallel to the buttons
of the same names (2 – 4) on the front panel .
For remote control, connect the corresponding
momentary pushbuttons to these connections .
If the timer insertion is not operated in combination
with the digital message insertion PA-1120DM, the
installation is terminated . Close the amplifier or the
basic unit with the housing cover .
If the timer is operated in combination with the
digital message insertion PA-1120DM, the following
steps have to be carried out additionally:
6) Install the digital message insertion PA-1120DM
according to the operating instructions supplied .
7) Make the following setting at the insertion
PA-1120DM . Place the jumper SEL 4 on the pins 1
and 2 (see operating instructions PA-1120DM,
chapter 4, item 4) .
8) Two 10-pole cables are supplied with the inser-
tion PA-1120DM . Put the cable with one inline
jack at each end into the pin housing CN4-1
of the PA-1120DM (see operating instructions
PA-1120DM, chapter 3, item 6) .
Put the second supplied cable into the inline
jack of the first cable and connect the stripped
core ends to the terminal strip CON 3 (t) accord-
ing to fig . 5 .
ST M 6 M 5
➄
Connection of the terminal strip CON 3
(for calling up announcements of the PA-1120DM)
PA-1200 C CLOCK MODULE
4 5
6
0 10
PROG.
LEVEL
M 4 M 3 M 2 M 1
CON 3
➃