Cutting Attachment; Fuel Safety - Husqvarna 129 RJ Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 29
M M uffler
Do not use an engine with a damaged muffler. A
damaged muffler increases the noise level and the
risk of fire. Keep a fire extinguisher near.
Examine regularly that the muffler is attached to the
product.
Do not touch the engine or the muffler when then
engine is on. Do not touch the engine or the muffler
for a while after the engine stops. Hot surfaces can
cause injuries.
A hot muffler can cause a fire. Be careful, if you use
the product near flammable liquids or fumes.
Do not touch the parts in the muffler, if the muffler is
damaged. The parts can contain some carcinogenic
chemicals.
Locknut
The locknut is used to lock some types of cutting
attachment (Picture 23).
When you install the locknut, tighten it in the opposite
direction to operation direction of the cutting attachment.

Cutting attachment

Do the regular maintenance. Let an approved
service center regularly examine the cutting
attachment to do adjustments or repairs.
The performance of the cutting attachment
increases.
The life of the cutting attachment increases.
The risk of accidents decreases.
Only use an approved cutting attachment guard. For
more information, see
Do not use a damaged cutting attachment.
Grass trimmer head
Make sure that you wind the grass trimmer line
tightly and equally around the drum to decrease the
vibration.
Use only the approved grass trimmer heads and
grass trimmer lines. See
15 .
Use a correct length of the grass trimmer line. A long
grass trimmer line uses more engine power than a
short grass trimmer line.
Make sure that the cutter on the cutting attachment
guard is not damaged.
Soak the grass trimmer line in water for 2 days
before you attach the grass trimmer line to the
product. This increases the life of the grass trimmer
line.
Grass blades and grass cutters
Use the product with an approved grass blade. Do
not use a grass blade without proper installation of
all required parts. Make sure that the installation is
done correctly and that the proper parts are used.
194 - 002 -
ACCESSORIES on page 15 .
ACCESSORIES on page
Inproper installation may cause the blade to fly off
and seriously injure the operator or the bystanders.
Wear protective gloves when you handle or do
maintenance on the blade.
Use head protection when you operate a product
with a grass blade.
Grass blades and grass cutters are used to cut
rough grass.
A grass blade can cause injury while it continues to
spin after the engine is stopped or the throttle trigger
is released. Make sure that the grass blade has
completely stopped rotating before any
maintenance.
Stop the engine before you do work on the cutting
attachment. Make sure the cutting attachment fully
stops. Disconnect the lead from the spark plug.
Only use an approved cutting attachment or a
correctly sharpened blade.
Keep the teeth of the blade correctly sharpened
(Picture 46).
Do not use a damaged cutting attachment.
Attach the transport guard to the grass blade when
you transport or store the product.
Blade thrust
A blade thrust is a sudden movement of the product
to the side, forward or rearward. A blade thrust
occurs when the grass blade or saw blade hits an
object that cannot be cut. In areas where it is not
easy to see the material being cut the risk of blade
thrust increases.
When a blade thrust occurs, there is a risk that the
product or the operator moves out of position. A
blade that moves can hit bystanders and there is a
risk of injuries.
If a blade is bent, has cracks, is broken or damaged,
discard the blade.
Use a sharp blade. The risk of blade thrust increases
when a blade is not sharp.

Fuel safety

Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry. Remove unwanted fuel from the
product.
If you spill fuel on your clothing, change clothing
immediately.
Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use a soap and water to
remove the fuel.
Do not start the engine if you spill oil or fuel on the
product or on your body.
Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
9

Publicité

Table des Matières
loading

Table des Matières