Description And Use; Warning; Caution; Installation - Vortice NORDIK DECOR 1S Notice D'emploi Et D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9
547 - Nordik Decor:Layout 1
ENGLISH

Description and use

The product you have purchased is a ceiling fan (fig.
1).

Warning:

!
this symbol indicates that care must
be taken to avoid injury to the user
• Do not use this product for functions other than
those described in the instruction booklet.
• After having removed the product from its packing,
ensure that it is complete and undamaged: if indoubt
contact Vortice Service Centre.
• Do not leave packaging within the reach of children
or differently able persons.
• Certain fundamental rules must be observed when
using any electrical appliance:
- Never touch appliances with wet or damp hands
- Never touch appliances while barefoot
• If using this appliance where there are children,
supervision by an adult is necessary; this appliance
must not be used, without assistance, by children or
persons whose physical, sensory or mental
capacities prevent them from applying the
necessary safety precautions.
• Do not use the appliance where flammable vapours
are present (spirit, insecticides, petrol, etc.).
• The lower section of the blade should raise fromthe
floor (Fig.2) by at least 2.30 metres, in accordance
with the provisions of the current laws inforce.
• Unauthorised changes to the factory set fittingshall
invalidate the guarantee and entitle the manu-
facturer to disclaim any whatsoever liability.

Caution:

!
this symbol indicates that care must
be taken to avoid damaging the appliance
• Do not make modifications of any kind to this
appliance.
• The appliance must not be exposed to atmospheric
conditions (rain, sun, etc.).
• The appliance must be installed by a professionally
qualified person.
• Regularly inspect the appliance for visible defects. If
any faults are found, do not operate the appliance
but contact Vortice Service Centre.
• The electrical mains to wich the unit is connected
must conform to current standard.
• The appliance must be properly connected to an
electrical system in compliance with the applicable
regulations and equipped with an efficient earthing
system. If in doubt, have a qualified electrician
perform a thorough check.
• The electrical power source to which the product
isto be connected must be able to provide the
maximum amount of electrical power required by the
product.If it cannot do this, contact an electrician for
appropriate remedial action.
• Use a multi-polar switch with minimum contact gaps
of 3 mm when installing the appliance.
01/10/2008
15.07
Pagina 7
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice.
• If the appliance does not function correctly or
develops a fault, turn it off and contact Vortice
immediately. Ensure that only genuine original
Vortice spares are used for any repairs.
• Do not leave the appliance on unnecessarily: when
the appliance is not in use, turn the switch to off.
• Use the unit at an ambient temperature not above
40°C (104°F).
• Place the unit at a suitable distance from
walls,objects, etc.
• Specifications
correspond to the electrical data on data plate A
(fig.3).

Installation

Figures: 4 - 19.
WARNING! The anchoring devices shown in figures 4
are purely indicative. Respect the instructions given
below to install the appliance.
1.Check that the intended ceiling is structurally suited
to support the weight of the product.
2.Pay attention that the anchoring devices do not
jeopardize the structural strength of the intended
ceiling.
3.Use correctly tightened anchoring devices suited to
the weight of the product and to the type of the
ceiling. Make sure that these are of a type that
cannot be unscrewed by the rotation of the product.
Fig.14a: component not present on all models.

Cleaning

Figures: 20 - 22.
Before cleaning the unit or carrying out maintenance
operations turn the main switch off and remove the
plug from the power supply.

Electrical Connections

Figure 23.
for
the
power
supply
must
7

Publicité

Table des Matières
loading

Table des Matières