General Operation; Infrared Remote Control - AEG MC 4414 CD/MP3 Mode D'emploi & Garantie

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
CAUTION:
Batteries are not to be disposed of together with domestic
wastes. Dispose of the used batteries at the relevant collection
bin or at your dealer's.
WARNING:
Do not expose the batteries to high temperatures or direct
sunlight. Never throw batteries into the fi re. There is a danger
of explosion!
CD deck transport protection
Press the FUNCTION button (6/8) repeatedly until „CD"
appears in the display.
Please open the CD compartment (11) by pressing the
OPEN/CLOSE button (12). The CD compartment opens
upwards.
Remove the transport protection from the CD player if
present before use.
Press the OPEN/CLOSE button (12) to close the CD
compartment (11) again.

General Operation

NOTE:
Some keys are to be found both on the device itself and
on the remote control. Keys with the same designation
have the same function.
ON/OFF / POWER (4/12)
Switch the device to the standby mode with the ON/OFF /
POWER button (the time is displayed). If this button is pressed
once more, the device switches on again.
Volume (5/10)
This is used to set the individual volume. The letters „VOL" and a
fi gure appear in the display (13). This corresponds to the volume
that has been set as far as „VOL 30" or „VOL 00".
PHONES Headphone Socket (21)
Please use headphones with a 3.5 mm stereo jack plug; these
should be inserted into the headphone socket. The loudspea-
kers are then switched off.
INTRO (7 on the remote control)
Press the INTRO button (INTRO appears in the display). Each
track on the CD is played for 10 seconds. Press this button again
to stop searching. The currently selected track is played.

Infrared remote control

For operating the music center from a distance of up to 5 metres
without a lead. If the range of the remote control is reduced, the
batteries have to be replaced. During operation ensure that there
is nothing blocking the direct line between the remote control
and the sensor (3) on the machine.
05-MC 4414 AEG 55
USB Connexion (7)
This device has been developed in accordance with the latest
technical developments in the USB fi eld. Unfortunately the large
number of different types of USB storage media on offer today
makes it impossible to guarantee full compatibility with all USB
storage media. For this reason there may be problems in rare
cases with playing back from USB storage media. This is not a
malfunction of the device.
1. In order to switch on the device please press the ON/OFF /
POWER switch (4/12).
2. Now press the FUNCTION button (6/8) to select the CARD-
USB mode.
3. Connect a USB storage medium. After a few seconds
the word „STOP" appears in the display together with the
number of folders, e.g. 04, and the total number of tracks.
4. Press II PLAY/PAUSE (14/1) to play back the music data.
For the method of operation, please see the section „Playing
CDs/MP3s".
NOTE:
The FIND function is restricted.
With the MEM +/MEM - (MEM UP/MEM DOWN) buttons
(19/4) you can select the individual folders.
CAUTION:
Before removing the USB storage medium, switch the device
to TUNER operation using the TUNER/BAND button (2/13).
AUDIO LINE IN (DVD/AUX) Input Sockets (24)
To connect analogue replay devices. With these sockets you
can also hear the sound from other playback devices such MP3
players, CD players etc through the loudspeakers.
1. Please connect the external device with an appropriate
cinch cable (2x RCA) to the AUDIO LINE IN sockets (24).
2. Press the FUNCTION button (6/8) repeatedly until „AUX"
appears in the display.
3. Through the loudspeakers you now hear the sound from the
external device; with the VOLUME buttons (5/10) you can
change the volume
4. For the remaining procedure please see the operating
instructions of the external sound source.
NOTE:
Adjust the volume of the external device to a comfortable level.
SUBWOOFER OUTPUT Socket (23)
In order to obtain better bass playback you can also connect an
active subwoofer.
Connect the active subwoofer with a cinch cable (1x RCA)
to the SUBWOOFER OUTPUT socket on the side of the
device.
55
01.08.2007, 11:42:05 Uhr

Publicité

Table des Matières
loading

Table des Matières