Fault Finding Chart - Flymo Contour Cordless 24 V Traduction Du Mode D'emploi Original

• WARNING
Remove the Battery Pack, before attempting
any maintenance or adjustment. Cutting head
con tinues to rotate after the trimmer has been
switched off. Keep fingers and hands clear of
the line cutter on leading edge of guard.
Caring for your Contour
After you have finished using your Flymo Contour follow
the procedure below:
1. Never clean your trimmer with water, cleaning fluids,
or solvents, just remove debris with a suitable tool,
a soft brush or dry cloth.
2. Using a soft brush, clean around the inside of the safety
guard, the cutting head (V) and the motor housing air
vents (W).
WARNING: Remove the Battery Pack before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS CLATTERING
NOISE
LINE SNAPS
CONTINUOUSLY
WHEEL STOPS TURNING
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
BATTERY DISPOSAL
• The battery must be removed from the product before
disposal (See Battery Replacement Section)
• This product contains a NiMH battery and should not be
discarded with normal household waste at the end of its
life.
• The battery should be taken to an Authorised Service
Centre or your local Recycling Station.
• Do NOT dispose of battery to water.
• NiMH batteries can be harmful and should be disposed
of through the recognised recycling facility in accord-
ance with European Regulations.
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional
application.
5012693-01 Contour Cordless 24V Euro.indb 4
Maintenance
3. Remove the wheel by pressing one of the buttons.
Clean the wheel (X) and groove (Y) on the trimmer head
with a soft brush.
4. Attach wheel as described in Wheel Assembly.
5. Inspect the trimmer carefully, especially the parts of the
cutting head.
6. If your trimmer is damaged in any way contact your
local Husqvarna service centre.
• Never use a damaged trimmer.
Storage
1. Store in a cool, dry place and out of reach of children.
Do not store outdoors.
2. Allow the product to cool for at least 30 minutes before
storing.

Fault Finding Chart

CHECK
Is the automatic line feed working?
Is the line fed out and visible?
Has line been removed from cleat?
Is the manual line feed working?
Has the motor reached full speed
before use?
Has too much line been fed out?
Is the line cutter missing from
the safety guard?
Are you using the trimmer correctly?
Is the line jamming on the spool?
Clean wheel and groove on trimmer head. SEE "MAINTENANCE"
Contact Husqvarna Customer Service
Environmental Information
• Do NOT incinerate.
The symbol
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the envi-
ronment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where you
purchased the product.
Service Recommendations
ENGLISH – 4
ACTION
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line and re­fit
No
spool and cap. SEE "CUTTING HEAD"
The line may be jammed on the spool.
No
Rewind line to remove crossed loops.
Check that line is in correct section of spool.
Allow the motor to reach full speed
No
before use.
Yes
SEE "MANUAL LINE FEED"
Contact your local approved Service Centre
Yes
or Husqvarna Customer Service.
Only use tip of nylon line to trim.
?
SEE "HOW TO TRIM AND EDGE"
Rewind the line on the spool, if symptoms
Yes
still persist, change spool and line.
on the product or on its packaging indi-
16.10.15 11:27