Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1. Power on the transmitter and connect a battery to
the ESC.
2. Press the setup button located on the ESC switch
and switch on the ESC.
3. Release the button as soon as the red LED starts to
flash.
4. Leave the throttle trigger at the neutral position and
press the setup button once.
5. Hold the throttle trigger at full throttle and press the
button a second time.
6. Hold the throttle trigger at full reverse/brake and
press the button a third time.
7. After three seconds the motor will respond to the
throttle commands.
ESC parameters
Certain function/performance parameters can be modi-
fied by using the setup button located on the ESC's
switch.
To modify the parameters, follow this procedure
1. With the ESC switched OFF, switch ON the transmit-
ter.
2. Switch ON the ESC while pressing the setup button
on the ESC switch.
3. The red LED flashes, keep pressing the button.
4. The green LED flashes once indicating parameter 1
(running mode).
4A. If you keep pressing the button, after 3 seconds
the green LED flashes twice indicating parameter 2,
if you still keep pressing the button, every 3 seconds,
the ESC moves to the next parameter and the green
LED flashes a number of times in relation with the
parameter number.
4B. When you release the button, the red LED flas-
hes in relation to the actual setting of the parame-
ter. For example, if you release the button when the
green LED is flashing 4 times (parameter 4 = start
mode punch), the red LED will flash 3 times indica-
ting setting 3 (Level 3).
5. Press the setup button once more to select to the
next available setting for the parameter. The red LED
now flashes 4 times, indicating setting 4 (Level 4).
6. To save the modification, switch OFF the ESC. When
you switch the ESC back ON, the new setting will be
used.
Programmable Items
1
Standard Parameters (adjustable with on/off switch)
1
Running Mode
Forward with
Brake
with Brake
2
Drag Brake Force
0%
3
Low Voltage
No Protection
Cut-Off Threshold
4
Start Mode (Punch)
Level 1
5
Max Brake Force
25%
36
INSTRUCTION MANUAL | MODE D'EMPLOI | BEDIENUNGSANLEITUNG
HIMOTO 1/10 OFF-ROAD CARS
Available parameters
1. Running Mode
A. "Forward Only with Brake"
In this mode the car can go forward and brake, there
is no reverse.
B. "Forward/Reverse with Brake"
In this mode the car can go forward and reverse
and can also brake. When you move the throttle
to the reverse position while the car is moving for-
ward, brakes are applied until the car stops, reverse
cannot engage while the car is moving. To engage
reverse, once the car has stopped, release the bra-
kes and move the throttle to the reverse position
again. While braking or in reverse, if the throttle is
moved to the forward position, the car will immedia-
tely accelerate forward.
2. Drag Brake Force
Sets the amount of brake automatically applied
when the throttle is returned to the neutral position.
This simulates the engine breaking effect of a real
car.
3. Low Voltage Cut-off
This function helps to prevent battery over-discharge
with the ESC continuously monitoring the bat-
tery's voltage. If the voltage becomes lower than the
threshold for 2 seconds, the output power is shut off
and the red LED flashes twice repeatedly. The cutoff
threshold calculation is based on LiPo individual cell
voltage.
4. Start mode "punch"
This parameter sets the initial throttle punch when
the car accelerates. Level1 gives a soft initial accele-
ration and level 4 gives a strong initial acceleration.
5. Maximum Brake Force
This parameter adjusts the maximum breaking
force. A higher value provides stronger braking, but
it also causes extra stress to the ESC and motor.
Parameters reset
With the throttle in the neutral position, press teh setup
button for 5 seconds, the red and green LED will flash
simultaneously indicating that the parameters have
been reset to the factory default values.
Optional programming card
An optional programming card can be bought sepa-
rately for modifying the brushless ESC's parameters
without having to use the setup button and LED.
Programmable Value
2
3
4
5
6
7
8
Forward/
Foward/
Reverse
Reverse
5%
10%
20%
40%
60%
80%
100%
2.6V/Cell
2.8V/Cell
3.0V/Cell
3.2V/Cell
3.4V/Cell
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
50%
75%
100%
Disable
HIMOTO 1/10 OFF-ROAD CARS
ESC calibration: enter calibration mode
1
ON/OFF
3
Release as
soon as soon as
the red LED
starts to blink
ESC calibration: calibrate with the help of the transmitter
1
9
LED
Level 9
WWW.NEIDHART.COM | WWW.HIMOTO.CH
2
Switch ON
Press and
hold the
SET button
LED
2
Press
Press
once
once
LED
Keep
pressing
the SET
button
3
Press
once
LED
37
Publicité
Table des Matières
