IMG STAGELINE DJP-106BT Mode D'emploi page 7

6.2 Reproduction via headphones
Use a 3 .5 mm plug to connect headphones
(minimum impedance: 32 Ω) to the jack
HP (13) . Adjust the volume with the control
VOL (15) .
CAUTION Never adjust the headphones to
a very high volume . Permanent
high volumes may damage your
hearing! Your ear will get accus-
tomed to high volumes which do not seem
to be that high after some time . Therefore,
do not further increase a high volume after
getting used to it .
6.3 Pairing the turntable with a
Bluetooth receiver
The turntable can only be paired with audio
units which are also used for audio repro-
duction, e . g . active speakers and amplifiers
with Bluetooth receiver . Tablet PCs and mobile
phones will not detect the DJP-106BT .
1) Switch on the turntable with the POWER
switch (3) .
2) Activate the Bluetooth function on the
audio unit to be paired with the DJP-106BT .
3) On the turntable, keep the button BT (11)
pressed for one second so that the blue
LED (12) on the right of the button starts
flashing slowly . Thus, the Bluetooth func-
tion has been activated .
If the audio unit has already been
paired with the DJP-106BT before, the
LED will light continuously after a while .
Thus, the wireless transmission has been
established .
4) If the audio unit has never been paired
with the turntable before, keep the button
BT pressed once again for two seconds
so that the blue LED starts flashing rap-
idly . Once the Bluetooth pairing has been
made, the LED will light continuously .
5) Use the control VOL (15) to adjust the
volume for the Bluetooth transmission .
6) To unpair, if required, keep the button BT
pressed for approx . two seconds until the
blue LED is off or simply switch off the
turntable .
7 Accessories
7.1 Replacement stylus
The stylus can be easily replaced, if required .
The corresponding parts are available from
your retailer, e . g . the stylus EN-24SP from
MONACOR .
To replace the stylus, remove the coloured
support of the stylus by pulling it forward . Put
the new stylus on the phono cartridge system .
7.2 Felt slipmat
To create scratch effects, a felt slipmat is re-
quired . The slipmat DJP-2M is available from
MONACOR .
8 Maintenance
8.1 Cleaning
To clean the turntable housing and the cover
only use a soft cloth, dry or slightly (not drip-
ping!) wet . Never use alcohol, chemicals or
aggressive detergents!
To dust the stylus and the records, the
corresponding accessories are available from
your retailer, e . g . the carbon fibre record
cleaning brush DC-100 from MONACOR .
8.2 Transport
When dispatching the turntable, make sure
to wrap the turntable and its components in
their original packaging or particularly secure
them for transport . Please note: Any damage
to the housing or the turntable due to careless
transport will not be covered by the guar-
antee; any resulting repairs will be charged!
When dispatching the turntable, always
observe the following precautions:
1) Put the protective cap on the stylus .
2) Secure the tone arm (8) with the lock (7) .
3) The original cardboard box will offer the
best protection .
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
9 Specifications
Turntable platter: . . . ∅ 298 mm, plastic
Drive: . . . . . . . . . . . . belt drive
Speeds: . . . . . . . . . . . 33 ¹∕
Starting torque: . . . . 0 .3 kg / cm
Wow and flutter: . . . < 0 .25 %
S / N ratio: . . . . . . . . . > 50 dB
Audio outputs
Line: . . . . . . . . . . . 200 mV, RCA
Headphones: . . . . . 200 mV/32 Ω,
Power supply: . . . . . . ⎓ 12 V via power
Ambient
temperature: . . . . . . . 0 – 40 °C
Dimensions
(W × H × D): . . . . . . . 420 × 115 × 360 mm
Weight: . . . . . . . . . . 3 .3 kg
Subject to technical modification .
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
rpm, 45 rpm
3
3 .5 mm jack
supply unit provided
and connected to
230 V/ 50 Hz
7