Scope Of Use; Electrical Grounding Instructions; Start-Up Procedures - Black & Decker BD 195/5-MY Manuel De L'utilisateur

handle is only for pulling the unit.
– Press the button as shown in fig. 2, in order to extend the
telescopic handle, then pull the handle towards the high (fig.
3) up to its complete extent: a click indicates that the handle is
fully extended.
H. Rear pocket for the housing of accessories (only for model
"BD 195/5-MY-P").
I. Storage box for accessories.
J. Power cable.

3. SCOPE OF USE

The compressor is designed for generating compressed air for tools
operated by compressed air.
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty will
be voided if the machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The machine is to be used only for its prescribed purpose. Any other
use is deemed to be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or injuries of any kind
caused as a result of this.

4. ELECTRICAL GROUNDING INSTRUCTIONS

This product should be electrically grounded. In the event of an
electrical short circuit, grounding reduces the risk of electrical shock by
providing an escape wire for electrical current. This product is equipped
with a cord having a grounding wire with an appropriate grounding
plug. The plug must be plugged into an outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
4.1 Connection of the mains plug
Important!
The wires in the mains lead fitted to this product are coloured in
accordance with the code shown in fig. 10.
● This product is double insulated and therefore does not require a
connection to earth.
● The 3 pin plug must comply to BS1363/A.
● Fuse must comply to BS1362.
If for any reason the 13 amp plug fitted to this product requires
replacement it must be wired in accordance with the following instruction:
Do not connect the brown (live) or blue (neutral) to the earth pin marked
'E' on the 3 pin plug.
Connect the Blue wire to the terminal marked Neutral (N). Connect
the Brown wire to the terminal marked Live (L). Ensure that the outer
insulation is gripped by the cord grip and that the wires are not trapped
when replacing the plug cover. The mains lead on this product is fitted
with a 13 amp (BS1363/A) plug. A 13 amp (BS1362) fuse must be
fitted in the plug.
If in doubt consult a qualified electrician
There are no user serviceable parts inside this product except those
referred to in the manual. Always refer servicing to qualified service
personnel. Never remove any part of the casing unless qualified to do
so; this unit contains dangerous voltages.
Warning!
For your protection if this product is to be used outdoors it should not
be exposed to rain or used in damp locations. Do not place the product
on damp surfaces, use a workbench if available. For added protection
use a suitable residual current device (R.C.D.) at the socket outlet.
Note: If the mains cable requires replacing it must be replaced with
an identical one and fitted by a qualified person.
5. PRE-START PROCEDURES
● Examine the machine for signs of transport damage. Report any
damage immediately to the company which delivered the compressor.
● Verify that the tanks have been drained and are clear of any
moisture or dirt.
16
● The compressor should be set up near the working consumer.
● Avoid long air lines and long supply lines (extensions).
● Make sure the intake air is dry and dust-free.
● Do not set up the compressor in damp or wet rooms.
● The compressor may only be used in suitable rooms (with good
ventilation and an ambient temperature from +5°C to +40°C). There
must be no dust, acids, vapours, explosive gases or inflammable
gases in the room.
● The compressor is designed to be used in dry rooms. It is prohibited
to use the compressor in areas where work is conducted with
sprayed water.
6. OPERATING INSTRUCTIONS

6.1 Start-Up Procedures

1. Verify that the On/Off switch is in the Off position.
2. Verify that the tank air pressure is at 0 PSI.
3. Attach the air hose to the discharge line (fig. 4).
4. Plug the unit into a properly grounded outlet.
5. Push the On/Off switch to On. The On/Off switch will light-up to
indicate the compressor is on. The compressor will automatically
cycle on and off to keep the tank pressure maintained .
6. Adjust the pressure regulator to the proper pressure setting
required for the air tool.
6.2 Shut-Off Procedures
1. Push in the On/Off switch to the Off position.
6.3 Connecting the accessories to the compressor
All the accessories are connected to the compressor using the
spiral cord (K) fitted with quick connects.
Insert the spiral cord (K) from the side of connector (M) in the
compressed air outlet (L) (fig. 4). Push connector (M) firmly until it
clicks in place.
Connect the accessory selected to the other end (P) of the spiral
cord (fig. 6): push fitting (Q) of the accessory firmly inside (P). A click
indicates that the accessory is connected.
When you have finished your work, switch off the compressor, drain
the compressed air receiver using the accessory connected dry (for
example, blowing with the gun empty), then disconnect the spiral cord
from the compressor, pulling back the external ring-nut (N) (fig. 5).
With the same procedure (pulling back the ring-nut of connector P),
disconnect the spiral cord from the accessory (fig. 7).
6.4 Blow gun
To remove dust and dirt.
PRESSURE LEVEL: 4 - 8 bar
Warning!
It is advisable to wear safety goggles when using the blow gun.
Warning!
Do not direct the jet of compressed air towards people or
animals. Take care not to blow dust and dirt towards yourself or
other persons.
USE
1) Connect the blow gun to the compressor as explained in
paragraph "6.3 - CONNECTING THE ACCESSORIES TO THE
COMPRESSOR".
2) Set operating pressure to the value indicated for this accessory
(see table 1).
3) Direct the blow gun towards the surface to be cleaned and press
the lever (R) (fig. 8). The flow of air can be regulated according to
how far you press down lever (R).
TIPS FOR USING THE BLOW GUN
Clean the carpets of your home or car mats very efficiently using the
blow gun. It is also ideal for keyboards, electrical items, refrigerators,
cameras, TV cameras, glassware and the filters of vacuum cleaners
(fig. 9).
Warning: when using the blow gun on delicate or precision equipment
(TV cameras, camera lenses, etc.) reduce the pressure of the jet to
minimum value.