Product Description And Specifications - Bosch GST 25 Metal Professional Notice Originale

12 | English
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for making separating cuts and
cut-outs in wood, plastic, metal, ceramic plates and rubber
while resting firmly on the workpiece. It is suitable for
straight and curved cuts. The saw blade recommendations
are to be observed.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) SDS twist cap for saw blade release
(2) On/off switch locking mechanism
(3) On/off switch
(4) Stroke rate preselection thumbwheel
(5) Base plate
(6) Sawdust blower device switch
(7) Orbital action adjusting lever
(8) Saw blade receptacle
(9) Guide roller
A)
(10) Saw blade
(11) Hood
(12) Guide for parallel guide
(13) Shock protection guard
(14) Handle (insulated gripping surface)
A)
(15) Anti-splinter guard
(16) Locking screw for parallel guide
(17) Parallel guide with circle cutter
1 609 92A 4TF | (26.03.2019)
(18) Circle cutter centring tip
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Jigsaw
Article number
Stroke rate control
Constant electronic control
Rated power input
No-load stroke rate n
Stroke
Max. cutting depth
– In wood
– In aluminium
– In steel (unalloyed)
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 82 dB(A); sound power level
93 dB(A). Uncertainty K = 5 dB.
Wear hearing protection
Vibration total values a
determined according to EN 62841-2-11:
Cutting boards with saw blade T 111 C:
a = 4 m/s
h,B
Cutting sheet metal with saw blade T 118 A:
a = 4 m/s
h,M
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
A)
not actually being used should also be taken into account.
A)
This may significantly reduce vibration and noise emissions
over the total working period.
A)
W
−1
min
0
mm
mm
mm
mm
kg
(triax vector sum) and uncertainty K
h
2 2
, K = 1.5 m/s ,
2 2
, K = 1.5 m/s .
GST 25 Metal
3 601 E16 0..
●
●
670
500–2600
24
80
25
15
2.7
/ II
Bosch Power Tools