Technical Data - Bosch GLI 18V-2200 C Professional Notice Originale

A)
(12) Battery release button
A)
(13) Battery
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Cordless worklight
Article number
Rated voltage
A)
Lighting duration , ap- min/Ah
prox.
Total luminous flux,
max.
Permitted ambient temperature
– during charging
B)
– during operation
and during storage
Recommended batter-
ies
Button cell V =
type
Recommended chargers
Protection rating
Data transmission
Bluetooth®
Signal range
Operating frequency MHz
range
Max. transmission mW
power
A) At maximum brightness incl. remaining operating time in
dimmed mode
B) Limited performance at temperatures < 0 °C
C) Only for inductive batteries
D) Applies only when battery cover is closed and locked
E) The mobile terminal devices must be compatible with
Bluetooth® Low Energy devices (version 4.1) and support the
Generic Access Profile (GAP).
Bosch Power Tools
F) The signal range may vary greatly depending on external condi-
The colour rendition of illuminated objects can be distorted.
System Requirements
Mobile device (tablet, smart-
phone)
GLI 18V-2200 C
3 601 D46 5..
Fitting
V= 14.4 18
35 44
Charging the battery (accessory)
Note: The battery is supplied partially charged. To ensure
lm 2200
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
°C 0 to +45
reducing its service life. Interrupting the charging process
does not damage the battery.
°C –20 to +50
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). A protective circuit
GBA 14.4V
switches the cordless worklight off when the battery is
GBA 18V...
drained.
(max. 7.0 Ah)
GBA 18V...W u
(max. 2.0 Ah)
3
CR 2032
AL 18... CV
To remove the battery (13), press the release button (12)
GAL 18V-...
(see figure B) and pull the battery backwards and out of the
GAL 18V-... C
cordless worklight. Do not use force to do this.
C)
GAL 18...W
Follow the instructions on correct disposal.
GAL 3680
GAX 18V-...
Putting the button cell into operation
IP 64
The cordless worklight is equipped with a button cell so that
(dust-proof and
it can be detected by the mobile device even if no battery
D)
splash-proof)
(13) is inserted, see figure B.
Remove the separating film between the button cell (11)
Bluetooth®4.1
and the button cell contact when using the tool for the first
E)
(Low Energy)
time.
F)
m 15
Unlock the locking mechanism of the battery cover (2) and
fold up the battery cover (3).
2402–2480
Unscrew the screw of the battery compartment cover and re-
move the battery compartment cover (10). Remove the film
<1
from the button cell contact and reattach the battery com-
partment cover with the screw.
Operation
Start-up
Inserting the Battery
Unlock the locking mechanism of the battery cover (2) and
fold up the battery cover (3).
Insert the charged battery (13) into the lamp head (4) until
you feel it engage and it is flush with the lamp head (4).
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
Android 4.3 (and newer)
iOS 9 (and newer)
Do not continue to press the on/off switch after the
worklight has been automatically switched off. This
can damage the battery. Ensure that the battery is
charged and that the cordless worklight has cooled down
before switching the cordless worklight on again.
1 609 92A 3WZ | (12.04.2018)
English | 11