Important Safety Instructions - Sharp MX-M266N Guide De Démarrage

The machine includes the document filing function, which stores document
image data on the machine's hard drive. Stored documents can be called
up and printed or transmitted as needed. Data such as an address book,
transaction report and so on are also stored on the hard drive. If a hard drive
failure occurs, it will no longer be possible to call up the stored document data.
To prevent the loss of important documents in the unlikely event of a hard drive
failure, keep the originals of important documents or store the original data
elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no
responsibility for any damages or loss due to the loss of stored document data.
This machine contains the software having modules developed by Independent
JPEG Group.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
Laser information
Wave length 785 nm ± 10 nm/-15 nm
Pulse times (6.03 µs ± 0.021 µs) / 7 mm
Output power Max 0.4 mW
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007).
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Shielded interface cables must be used with this equipment to maintain
compliance with EMC regulations.
A cable of 10 m or less is preferable.
The equipment should be installed near an accessible socket outlet for easy
disconnection.
Each instruction also covers the optional units used with these products.
EMC (this machine and peripheral devices)
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
For the users of the fax function
FAX interface cable and Line cable
These special accessories must be used with the device.
The Declaration of Conformity is included in optional Facsimile expansion
kit (MX-FX11).
(Note)
Use modular cable of 10m or less length to connect an external telephone.

Important safety instructions

• If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to the
telephone network.
• Never install telephone wiring during a lightning storm.
• Never install telephone socket in wet locations unless the socket is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care
not to spill any liquids on the machine.
• Save these instructions.
Software licence
The SOFTWARE LICENCE will appear when you install the software from the
CD-ROM. By using all or any portion of the software on the CD-ROM or in
the machine, you are agreeing to be bound by the terms of the SOFTWARE
LICENCE.
• The explanations in this manual assume that you have a working knowledge
of your Windows or Macintosh computer.
• For information on your operating system, please refer to your operating
system manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for
Windows 7 in Windows environments. The screens may vary depending on
®
the version of the operating system.
• This manual contains references to the fax function. However, please note
that the fax function is not available in some countries and regions.
• This manual contains explanations of the PC-Fax driver and PPD driver.
However, please note that the PC-Fax driver and PPD driver are not available
and do not appear on the software for installation in some countries and
regions.
In this case, please install the English version if you want to use these drivers.
• Considerable care has been taken in preparing this manual. If you have any
comments or concerns about the manual, please contact your dealer or
nearest authorised service representative.
• This product has undergone strict quality control and inspection procedures.
In the unlikely event that a defect or other problem is discovered, please
contact your dealer or nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for
failures occurring during the use of the product or its options, or failures due
to incorrect operation of the product and its options, or other failures, or for
any damage that occurs due to use of the product.
This product is designed for commercial application only and as such it falls
outside the scope of Regulation (EC) 1275/2008 implementing EU Directive
2005/32/EC on eco-design requirements for standby and off mode electric
power consumption. Sharp does not recommend the product for domestic
application and will not accept any liability for such use.
Warranty
While every effort has been made to make this document as accurate and
helpful as possible, SHARP Corporation makes no warranty of any kind with
regard to its content. All information included herein is subject to change
without notice. SHARP is not responsible for any loss or damages, direct or
indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2015. All rights reserved. Reproduction,
adaptation or translation without prior written permission is prohibited, except
as allowed under copyright laws.
Safety data sheet
The SDS (Safety Data Sheet) can be viewed at the following URL address:
http://www.sharp-world.com/corporate/eco/env-info/sds/index.html
Notice for users in the UK
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is
either a non-rewireable (moulded) or a rewireable type. Should the fuse need to
be replaced, a BSI or ASTA approved fuse to BS1362 marked
and of the same rating as the one removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never
use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with
the plug supplied either cut-off the moulded plug (if this type is fitted) or remove
by undoing the screws if a rewireable plug is fitted and fit an appropriate type
observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the
plug destroyed immediately and disposed of in a safe manner. Under no
circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the
following code:
GREEN-AND-YELLOW:
BLUE:
BROWN:
As the colours of the wires in this mains lead may not correspond with coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the
terminal in the plug which is marked with the letter E, or by the safety earth
symbol , or coloured green or greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is
marked with the letter L or coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
Noise emission
Noise emission values
The following shows noise emission values as measured according to ISO7779.
Sound power level L
WAd
Operating (continuous printing)
Standby mode (Low power level mode) 3.3 B
Sound pressure level L
pAm
Operating
Bystander positions 55 dB
(continuous printing)
Standby mode Bystander positions 14 dB
• Operating: with options MX-CS13 + MX-CS12 + AR-DS20 + MX-FN26
3
or
Earth
Neutral
Live
MX-M266N MX-M316N
7.2 B 7.3 B
3.4 B
MX-M266N MX-M316N
55 dB
14 dB