Using Your Television; Setting The V-Chip - Insignia NS-27RTV Guide De L'utilisateur

Using your television

Notes • If you select a channel with no
broadcast signal, the sound is
automatically muted.
• If a station you are viewing stops
broadcasting, the television
automatically shuts itself off after 15
minutes.
To use the television:
1 Press POWER to turn on the television.
2 Adjust the volume level by pressing VOL +
or –. The volume level is indicated on the
screen by green bars. As the volume level
increases, so do the number of bars. If the
volume decreases, the number of green bars
also decreases.
3 Set the TV/CABLE menu option to the
appropriate position (see "Selecting TV or
cable" on page 9).
4 Press the direct channel selection buttons to
select the channel.
Selecting analog channels
Channels Press
1-9 Press 0 twice, then 1-9 as needed.
Example: to select channel 2, press
0 0 2.
10-99 Press 0, then the remaining 2 digits.
Example, to select channel 12, press
0 1 2.
100-125 Press the 3 digits in order. Example,
to select channel 120, press 1 2 0.
Selecting digital channels
Press the first 3 digits, then press the
–/DISPLAY button, followed by the remaining
3 digits.
Example, to select channel 015-001, press 0 1 5
– 0 0 1.
TV Cable
VHF VHF
2-13 2-13
UHF STD/HRC/IRC
14-69 14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01 (5A)
Seeking channels
To seek the next channel:
Press and release CH
automatically stops at the next channel set into
memory.
For proper operation, before seeking channels,
they should be set into the memory. See
"Memorizing channels" on page 9.
10
or . The channel
www.insignia-products.com
Viewing information
To view program information:
1 Press -/DISPLAY to display the current
information on the screen.
When the television receives a digital signal,
the digital information appears:
• Broadcast program name
• Station name
• Remaining time
• Audio language
• Program name
• V-Chip rating
• V-Chip mark
• Closed caption mark
When the television receives an analog
signal, -/DISPLAY shows only analog
information.
2 Press -/DISPLAY again. The analog
information appears.
• Clock
• Channel number or video mode selected
• Channel label (if preset)
• Stereo or SAP (second audio program)
audio status
• Content rating
• On timer, Off timer, Sleep time (if preset)
• Picture size
3 Press -/DISPLAY again to clear the call
display.
Viewing the previous channel
The QUICK VIEW button allows you to go back
to the last channel viewed. Press QUICK VIEW
again to return to the last channel you were
watching.
Muting the volume
Press MUTE to turn off the sound. The
television's sound is silenced and MUTE
appears on the screen. The sound can be
switched back on by pressing this button again
or by pressing one of the VOL + or – buttons.
Using sleep
To set the television to turn off after a preset
amount of time, press SLEEP on the remote
control. The clock counts up ten (10) minutes for
each press of the SLEEP button (0h00m,
0h10m, ...1h50m, 2h00m).
After the sleep time is programmed, the display
appears briefly every ten minutes to remind you
that the sleep timer is operating. To confirm the
sleep timer setting, press SLEEP and the
remaining time is displayed for a few seconds. To
cancel the sleep timer, press SLEEP repeatedly
until the display turns to 0h00m.

Setting the V-Chip

An age limitation can be set to restrict children
from viewing or hearing violent scenes or
pictures that you may choose to exclude. The
restriction applies to TV rating and movie rating
if this data is transmitted. You may set this
restriction separately. To use the V-Chip
function, you must set a password.
NS-27RTV 27-inch Color TV