Bosch PWS Universal Notice Originale page 19

OBJ_BUCH-2491-002.book Page 19 Monday, June 29, 2015 10:35 AM
Technical Data
Angle Grinder
Article number
Rated power input
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 29.06.2015
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
Bosch Power Tools
PWS Universal PWS Universal
3 603 CA2 0.. 3 603 CA2 4 ..
W 701
-1
min 11000
mm 115
M 14
mm 21

kg 1.7
kg 1.7
/II
Protection Guard for Grinding
of the work process. For this, press the release lever 1 up-
ward and turn the protection guard 6 to the required position.
 Always adjust the protection guard 6 in such a manner
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 6.
 Adjust the protection guard 6 in such a manner that
sparking is prevented in the direction of the operator.
 The protection guard 6 may be turned only upon actua-
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 10.
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 10 is mounted in the same
manner as the protection guard for grinding 6.
English | 19
+ +
PWS Universal 125
3 603 CA2 7..
750 850
12000 12000
115 125
M 14 M 14
21 21
 
1.8 1.8
1.8 1.8
/II /II
Place the protection guard 6 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 6 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
tion guard 6 to the requirements
1 609 92A 1CA | (29.6.15)