Technical Data; Noise/Vibration Information; Battery Charging - Bosch UniversalMulti 12 Notice Originale

18 | English
(8) Thread for auxiliary handle
(9) Tool holder
(10) Worklight
(11) Plunge cut saw blade
A)
(12) Sanding plate
A)
(13) Sanding sheet
A)
(14) Depth stop
(15) Segment saw blade
(16) Handle (insulated gripping surface)
(17) Dust extraction hose
(18) Dust extraction outlet
(19) Dust extraction system
(20) Clamping lever for dust extraction system
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Cordless multifunction tool
Article number
Orbital stroke rate
preselection
Constant electronic control
Soft start
AutoClic tool holder
Rated voltage
No-load speed n
0
Oscillation angle on left/
right
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– During charging
A)
– During operation and
during storage
Recommended batteries
Recommended chargers
A) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.

Noise/Vibration Information

Noise emission values determined according to
EN 62841‑2‑4.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power level
94 dB(A). Uncertainty K=3 dB.
Wear hearing protection
1 609 92A 4N3 | (16.10.2018)
A)
A)
A)
A)
A)
A)
UniversalMulti 12
3 603 A03 0..
V=
−1
min 10000–20000
°
kg
°C 0 to +45
°C –20 to +50
PBA 10.8 V...
PBA 12 V...
AL 11.. CV
GAL 12..
Working without the Auxiliary Handle
Vibration total values a
determined according to EN 62841‑2‑4 (sanding),
EN 62841‑2‑11 (cutting):
Sanding: a =4 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
Working with the auxiliary handle
Vibration total values a
determined according to EN 62841‑2‑4 (sanding),
EN 62841‑2‑11 (cutting):
Sanding: a =6 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
●
increase the vibration and noise emissions over the total
working period.
●
To estimate vibration and noise emissions accurately, the
●
times when the tool is switched off or when it is running but
● not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
12
over the total working period.
Implement additional safety measures to protect the oper-
1.4
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
1.1
Fitting
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
(triax vector sum) and uncertainty K
h
2 2
, K=1.5 m/s ,
2
=10 m/s
h
=12 m/s
h
(triax vector sum) and uncertainty K
h
2 2
, K=1.5 m/s ,
2
=17 m/s
h
=16 m/s
h
Bosch Power Tools
2
, K=1.5 m/s ,
2 2
, K=1.5 m/s .
2
, K=2 m/s ,
2 2
, K=1.5 m/s .