Bosch GKS 65 Professional Notice Originale page 16

16 | English
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool must not be used to cut ferrous metals.
The power tool is intended for making straight cuts in wood
with and against the grain and mitre cuts in wood while rest-
ing firmly against the workpiece.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
(2) Lock-off button for on/off switch
(3) Speed preselection thumbwheel (GKS 65 GCE)
(4) Auxiliary handle (insulated gripping surface)
(5) Spindle lock button
(6) Scale for mitre/bevel angles
(7) Wing bolt for parallel guide
(8) Clamping lever for mitre/bevel angle preselection
(9) Cut mark 0°
(10) Cut mark 45°
A)
(11) Parallel guide
(12) Retracting blade guard
(13) Base plate
(14) Adjusting lever for retracting blade guard
(15) Chip ejector
(16) Protective guard
1 609 92A 4LP | (19.11.2018)
(17) Handle (insulated gripping surface)
(18) Hex key
(19) Clamping bolt with washer
(20) Clamping flange
A)
(21) Circular saw blade
(22) Mounting flange
(23) Saw spindle
(24) Fastening screw for dust extraction adapter
(25) Dust extraction adapter
(26) Clamping lever for cutting depth preselection
(27) Cutting depth scale
Wing bolt for mitre/bevel angle preselection
(29) Pair of screw clamps
A)
(30) Guide rail
A)
(31) Connector
A)
(32) Extraction hose
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-5.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 89 dB(A); sound power level
100 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-5:
2
Sawing wood: a = 3.0 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
A)
A)
A)
2
, K = 1.5 m/s .
Bosch Power Tools