Before Start-Up - KENT 26D Instructions D'utilisation

INSTRUCTIONS FOR USE

BEFORE START-UP

WARNING!
At every machine start-up, check that, between
the deck (4 or 5, Fig. C) and the machine or
between the squeegee (12, Fig. C) and the
machine, there is no foreign material which
may prevent the deck and the squeegee from
lifting. This check is necessary because, if the
machine has been turned off without lifting the
deck and the squeegee, when turned on again,
the deck and the squeegee lift automatically.
Deck installation/removal
The machine can be equipped with either the
brush/pad-holder deck (4, Fig. C) or the cylindrical brush deck
(5).
For deck installation/removal see the procedure in
Maintenance chapter.
NOTE
When the deck is installed/removed, it may be
necessary to change the squeegee too,
because they must have the same width. For
correct deck and squeegee matching, see the
Technical Data paragraph.
Brush/pad-holder installation/removal
1. According to the kind of cleaning to be carried out, the
machine can be equipped either with brushes (8, Fig. K)
or pad-holders (9) with pads (10) together with the
appropriate deck.
For the installation/removal, proceed as follows.
2. Insert the ignition key (12, Fig. B) and turn it to "I".
WARNING!
Before pressing the switch (4, Fig. B), always
check that, between the deck (4, Fig. C) and the
machine there is no foreign material which may
prevent the deck from lifting.
3. Lift the deck by pressing the switch (4, Fig. B).
4. Turn the ignition key (12, Fig. B) to "0" and remove it.
5. Install the brushes/pad-holders (8 or 9, Fig. K) and lift
them completely, then turn them clockwise (see the
arrows in Fig. K) until the end of stroke.
6. To remove the brushes/pad-holders, carry out steps 2 to
5 in the reverse order.
10
Cylindrical brush installation/removal
7. Insert the ignition key (12, Fig. B) and turn it to "I".
8. Lift the deck by pressing the switch (4, Fig. B).
9. Turn the ignition key (12, Fig. B) to "0" and remove it.
10. On both sides of the machine, unscrew the knobs (17,
Fig. K) and remove the side skirt assemblies (16).
11. Unscrew the knobs (21, Fig. K) and remove the doors
(20) by pushing the knobs downwards.
12. Install the cylindrical brushes (19).
The cylindrical brushes can be installed on either sides.
13. Install the doors (20, Fig. K) and fix them with the knobs
(21).
14. To remove the cylindrical brushes, carry out steps 7 to 13
in the reverse order.
Squeegee installation
15. Install the squeegee (12, Fig. C) and fasten it with the
handwheels (15), then connect the hose (11) to the
squeegee.
16. Using the handwheel (16, Fig. C), adjust the squeegee
so that its rear blade (18) - in all its length - touches the
floor and that the front blade (17) is slightly detached
from the floor.
Solution tank filling
17. Open the cover (13, Fig. I).
18. Fill the solution tank (16, Fig. I) with a solution suitable
for the work to be carried out.
Do not fill the solution tank completely, leave few inches
from the edge.
Always follow the dilution instructions on the label of the
chemical product used to create the solution.
The solution temperature must not exceed 104°F
(40°C).
Operator's position adjustment
19. Using the lever (1, Fig. C), adjust the inclination of the
steering wheel (2) to reach a comfortable position.
Razor Blade 26D/28D – Razor Blade 28C — 909 6457 000(2)2006-11
WARNING!
Before pressing the switch (4, Fig. B), always
check that, between the deck (5, Fig. C) and the
machine there is no foreign material which may
prevent the deck from lifting.
NOTE
The squeegee and the deck must have the
same width. For correct deck and squeegee
matching, see the Technical Data paragraph.
CAUTION!
Use only low-foam and non-flammable liquid
detergents, intended for automatic scrubber
applications.