Tank Emptying; After Using The Machine; Pushing/Towing The Machine; Machine Long Inactivity - KENT 26D Instructions D'utilisation

INSTRUCTIONS FOR USE
Battery discharge during operation
6. Until the green warning light (7a, Fig. B) stays on, the
batteries allow the machine to work normally.
When the green warning light (7a) turns off and first the
yellow warning light (7b) and then the red warning light
(7c) turn on, it is necessary to charge the batteries.
– When the yellow warning light (7b) turns on, the
machine residual autonomy will last for a few
minutes (depending on battery type).
– When the red warning light (7c) turns on the machine
autonomy is over: after a few seconds the
brushes/pad-holders are automatically stopped and
the deck is automatically lifted. Only the machine
vacuum and drive systems still operate, just to dry
the wet floor and move the machine to the charging
area.
CAUTION!
Do not use the machine with discharged
batteries, to avoid damaging the batteries and
reducing the battery life.
NOTE
In case the machine drive system cannot be
used to move the machine, see
Pushing/towing the machine paragraph.

TANK EMPTYING

An automatic float shut-off system (5, Fig. I) stops the vacuum
system when the recovery water tank (15) is full.
The vacuum system deactivation is signaled by a sudden
increase in the vacuum system motor noise frequency.
When the recovery water tank (15, Fig. I) is full, empty it
according to the following procedure.
Recovery water tank emptying
1. Stop the machine by releasing the pedal (3, Fig. C).
2. Lift the brush/pad-holder deck and the squeegee by
pressing the switch (4, Fig. B).
3. Drive the machine to the appointed disposal area.
4. Empty the recovery water tank through the hose (10, Fig.
C). After working, rinse the tank with clean water.
Solution tank emptying
5. Carry out steps 1 to 3.
6. Empty the solution tank using the tap (24, Fig. C). After
working, rinse the tank with clean water.
12

AFTER USING THE MACHINE

After working, before leaving the machine:
1. Remove the brushes/pad-holders according to the
procedure shown in the relevant paragraph.
2. Empty the tanks (15 and 16, Fig. I) according to the
procedure shown in the previous paragraph.
3. Perform the daily maintenance procedures (see the
Maintenance chapter).
4. Store the machine in a clean and dry place, with the
brushes/pad-holders and the squeegee lifted or
removed.

PUSHING/TOWING THE MACHINE

To push/tow the machine easily when the drive system
cannot be used, unlock the electromagnetic brake (27, Fig. C)
according to the following procedure:
1. Screw down completely the internal screws (29, Fig. C)
(by turning them clockwise) with the supplied key.
2. When pushing/towing procedure is over, unscrew the
screws (29, Fig. C) for 3 turns approximately, to lock the
electromagnetic brake (27).

MACHINE LONG INACTIVITY

If the machine is not going to be used for more than 30 days,
proceed as follows:
1. Perform the procedures shown in After using the
machine paragraph.
2. Disconnect the battery red connector (4, Fig. J) by
proceeding as follows:
– Lift the covers (1 and 13, Fig. I) and check that the
tanks (15 and 16) are empty, otherwise drain them
through the drain hose (10, Fig. C) and the tap (24).
– Close the covers (1 and 13, Fig. I).
– Carefully lift the tank assembly (1, Fig. J).
3. Drain the detergent supply system, according to the
procedure described in the Maintenance chapter [only
for machine equipped with detergent supply system
(optional)].

FIRST PERIOD OF USE

After the first 8 hours, check the machine fastening and
connecting parts for proper tightening. Check the visible parts
for integrity and leakage.
Razor Blade 26D/28D – Razor Blade 28C — 909 6457 000(2)2006-11
WARNING!
If the screws (29, Fig. C) are not unscrewed as
shown, the electromagnetic brake is
deactivated.
WARNING!
Do not start the machine when the
electromagnetic brake unlocking screws (29,
Fig. C) are screwed (electromagnetic brake
deactivated).