Air Flow Velocity And Direction Adjustment; Econo Cool Operation; Timer Operation (On/Off Timer) - Mitsubishi Electric MSZ-A09YV Notice D'utilisation

AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT

AIR FLOW velocity and direction can be selected as required.
I
To change the AIR FLOW velocity, press the
Each time the button is pressed, the fan speed is changed in sequence:
(Low) →
• Use the
˚C
• If the operating sound of the air conditioner disturbs your sleep, use the
CLOCK
AMPM
AMPM
I
To change the AIR FLOW blowing direction vertically, press the
TOO TOO
ON/OFF
VANE
WARM COOL
Each time the button is pressed, the angle of the horizontal vane is changed in
sequence:
(AUTO)
FAN STOP
I FEEL
HEAT
AUTO
SWING OPERATION
VANE START
Use the swing operation for the air flow to reach all corners of the room.
DRY COOL
MODE HR.
Recommended horizontal vane range
ECONO COOL MIN.
Use the
Use position
RESET CLOCK
and use positions
when adjusting to your requirements.
NOTE:
• In the cooling operation, when the air conditioner is operated with setting the horizontal vane to
(4) or (5) for 1 hour, the AIR FLOW direction is automatically set to horizontal to prevent condensed water from
dropping.
• Adjust the vertical AIR FLOW direction using the remote controller. If the horizontal vane is moved manually, it may
cause trouble.
• In the heating operation, if the air flow temperature is too low or when defrosting is being done, the horizontal vane
position is set to (1).
Auto air flow direction control operation
VANE
When the AUTO mode is selected with the
ton, the position of the horizontal vane is automati-
cally set to correspond to the operation mode for
effective operation.
(1) HEAT
• When the air flow temperature is too low, the air is
blown out horizontally.
• When the air flow temperature rises, the air is blown
out downwards.
(2) COOL, DRY
The air is blown out horizontally.
NOTE:
• When the operation mode changes in " (AUTO)"
mode, the horizontal vane is automatically
changed to the position in each mode.
8
FAN
(Med.) → (High) →
(AUTO)
(High) notch to cool/heat the room more.
(Low) notch.
button.
(1) → (2) → (3) → (4) → (5) →
(AUTO) position usually.
(1) or (2) in the COOL or DRY mode
(3) to (5) in the HEAT mode
I
To change the horizontal direction of the air
flow, move the vertical vane manually.
but-
Adjust the vane before operation starts.
Since the horizontal vane moves automatically, your
fingers may be caught.

ECONO COOL OPERATION

Use this operation when you want to be comfortable in COOL mode even with energy saved.
button.
CLOCK
TOO
ON/OFF
WARM
(SWING) →
FAN
I FEEL
HEAT AUTO
VANE
DRY COOL
MODE
ECONO COOL
1 RESET CLOCK
COOL
2
DRY
What is "ECONO COOL"?
3
Swing air flow (change of air flow) makes you feel cooler than constant air flow. So, even though the set temperature is
HEAT 4
automatically set 2°C higher, it is possible to perform cooling operation with keeping comfort. As a result, energy can be saved.
5

TIMER OPERATION (ON/OFF TIMER)

It is convenient to set the timer when you go to bed, when you get home, when you get up, etc.
How to set the ON timer
1
START
Press the
Each time the button is pressed, the ON timer mode
alternates between ON and OFF.
2
Set the time of the timer using the
MIN.
buttons.
HR.
Each time the
creases by 1 hour; each time the
the set time increases by 10 minutes.
To release the ON timer:
I
START
Press the
Programming timer operation
The ON timer and the OFF timer can be used in combination. The timer of the set time that is reached first will operate first.
(" " mark indicates the order of timer operations.)
• If the current time has not been set, the timer operation cannot be used.
NOTE:
If the main power is turned off or a power failure occurs while AUTO START/STOP timer is active, the timer setting is
cancelled. As these models are equipped with an auto restart function, the air conditioner starts operating with timer
cancelled at the same time that power is restored.
Perform the following operations while the unit is operat-
ing in the MANUAL COOL mode.
I
ECONO COOL
Press the button.
˚C
AMPM
When the (ECONO COOL) operation is selected in COOL mode, the air
conditioner performs swing operation in various cycle according to the tempera-
AMPM
ture of air conditioner.
TOO
Also SET TEMPERATURE is automatically set 2°C higher than in COOL mode.
COOL
To release the ECONO COOL operation:
I
ECONO COOL
Press the button again.
STOP
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
START
VANE
• When the button is pressed or the operation mode is changed during
HR.
the ECONO COOL operation, ECONO COOL operation is released.
MIN. TOO
FAN WARM
• The button, the or
are available.
How to set the OFF timer
1
button during operation. Press the
Each time the button is pressed, the OFF timer mode
alternates between ON and OFF.
HR. 2
and Set the time of the timer using the
MIN.
button is pressed, the set time in- Each time the
MIN.
button is pressed, creases by 1 hour; each time the
the set time increases by 10 minutes.
To release the OFF timer:
I
Press the
button.
TOO
COOL
button and ON/OFF timer (explained below)
STOP
button during operation.
HR.
and
buttons.
HR.
button is pressed, the set time in-
MIN.
button is pressed,
STOP
button.