Technical Data; Before Using The Equipment - EINHELL TE-AG 18/115 Li Traduction Du Mode D'emploi D'origine

The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
Rated speed: ............................. 8500 min
Max. wheel diameter: .................4½ in. (115 mm)
Grinding wheels: ...................4½ x 0.86 x 0.23 in.
................................................. (115 x 22 x 6 mm)
Cutting wheel: .......................4½ x 0.86 x 0.12 in.
................................................. (115 x 22 x 3 mm)
Mounting spindle thread: .................... ⅝ -11 UNC
Weight: ............................................ 4 lbs (1.8 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
Anl_TE_AG_18_115_Li_SPK7_USA.indb 14 Anl_TE_AG_18_115_Li_SPK7_USA.indb 14
EN
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before using the equipment

Warning!
Always remove the battery pack before
making adjustments to the equipment.
(rpm)
-1
5.1 Fitting the additional handle (Fig. 2)
•
The angle grinder must not be used without
the additional handle (3).
•
The additional handle can be secured in any
of three positions (A, B, C).
Tool side
Left (position A / as
shown)
Right (position B)
Top (position C)
5.2 Replacing and adjusting the guard (Fig. 3)
Replacing:
•
Remove the flange nut (7) and the clamping
flange (6) underneath.
•
Open the clamp lever (10) on the guard (4).
•
Turn the guard (4) through 180° in clockwise
direction so that the guard points upwards.
•
Remove the guard (4).
To mount, proceed in the reverse order.
Adjusting:
•
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
•
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
clamp lever (10) and turn the cover (4) into
the required position.
•
Ensure that the guard (4) correctly covers the
gear wheel casing.
•
Secure the clamp handle (10) again.
- 14 -
Suitable for
Right-handed users
Left-handed users
Using cutting wheels
23.01.2019 15:18:41 23.01.2019 15:18:41