Makita DTD155 Manuel D'instruction page 2

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
No load speed (RPM)
Impacts per minute
Rated voltage
Overall length
Standard battery cartridge
Charger
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
Machine screw
Standard bolt
High tensile bolt
Hard impact mode
Soft impact mode
Hard impact mode
Soft impact mode
4 mm - 8 mm (5/32" - 5/16")
5 mm - 14 mm (3/16" - 9/16")
5 mm - 12 mm (3/16" - 1/2")
BL1815N, BL1820B, BL1830, BL1830B, BL1840B, BL1850B, BL1860B
DC18RC, DC18RD, DC18SD, DC18SE, DC18SF
1.2 - 1.5 kg (2.6 - 3.2 lbs)
Do not expose power tools to rain or wet con-
3.
ditions. Water entering a power tool will increase
the risk of electric shock.
Do not abuse the cord. Never use the cord for
4.
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
Use personal protective equipment. Always
2.
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
2 ENGLISH
DTD155
0 - 3,000 /min
0 - 1,300 /min
0 - 3,900 /min
0 - 1,600 /min
D.C. 18 V
135 mm (5-5/16")