Whirlpool W11339718A Guide D'utilisation Et D'entretien page 25

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
If you experience
Washer Not Performing As Expected (cont.)
Washer won't run or fill;
washer stops working
(cont.)
Washer not draining/
spinning; loads are
still wet
Possible Causes
The load size is being sensed.
Normal washer operation.
The washer door is not firmly shut.
On some models: The Load & Go™
bulk dispenser is not fully seated in
the washer.
Washer not loaded as recommended.
Not using HE detergent or using too
much HE detergent.
Door not opened between cycles.
Drain hose extends into standpipe
farther than 4.5" (114 mm).
The drain hose is clogged, or the
end of the drain hose more than
96" (2.4 m) above the floor.
Strainer/stocking on end of
drain hose.
The drain hose fits too tightly
in the standpipe, or it is taped
to the standpipe.
Solution
After the load size is sensed, the estimated time based on
load size will be displayed and water will be added.
Door must be completely closed and latched for washer
to run.
The washer pauses for about 2 minutes during certain cycles.
Allow the cycle to continue. Some cycles feature periods of
tumbling and soak.
Washer may be stopped to reduce suds. Use only a proper
amount of HE detergent.
Cold Wash uses less water in the beginning of the cycle to
provide a high concentration of detergent for optimal cleaning
action. Following this concentrated tumbling, more water is
used to complete the wash.
During the first 20 minutes of the Clean Washer with affresh
cycle, it will activate the steamer but the drum will not spin or
fill with water. You may see condensation on the door window
during this initial phase. If you are using an affresh
Cleaner tablet, it will not dissolve completely during the steam
phase. This is normal.
The door must be closed during operation.
Make sure that the Load & Go™ bulk dispenser is fully seated
in the washer, and that the lid on the bulk dispenser is
firmly closed.
Remove several items and rearrange load evenly in washer
drum. Close door; then touch and hold START/PAUSE.
Do not add more than one or two additional items after cycle
has started to avoid tightly packing or unbalancing.
Do not add more water to the washer.
Only use HE detergent. Suds from regular detergents can
slow or stop the washer. Always measure detergent, following
manufacturer's directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN with
EXTRA RINSE. Touch START/PAUSE. Do not add more
detergent.
Make sure the Load & Go
are using a single dose of detergent.
After any wash cycle is completed, the door must be opened
and then closed before a new cycle can begin.
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over
drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Requirements" in Installation Instructions.
Remove strainer/stocking from drain hose.
The drain hose should be loose yet fit securely. Do not
seal the drain hose with tape. The hose needs an air gap.
See "Secure the Drain Hose" in Installation Instructions.
Washer
®
bulk dispenser is disabled if you
®
25

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

W11339719a - sp

Table des Matières