Service Menu - Lamborghini Caloreclima FL 32 MCA Instructions D'utilisation

FL 32 MCA
Heating power adjustment
To adjust the heating power, switch the boiler to TEST mode (see sec. 4.1). Press the heating buttons (detail 3 - fig. 1) to increase or decrease the power (min. = 00 - max. = 100).
Press the reset button within 5 seconds and the max. power will remain that just set. Exit TEST mode (see sec. 4.1).
Configuration Menu
Press the DHW buttons together for 10 seconds to access the configuration Menu. 8 parameters are available, indicated by the letter "b", which are not modifiable from Remote
Timer Control.
Press the Heating buttons to scroll the list of parameters in increasing or decreasing order. Press the DHW buttons to view or modify the value of a parameter: the modification will
be automatically saved.
Contents Description
b01 Gas type selection
b02 Boiler type selection
b03 Combustion chamber type selection
Primary Exchanger type selection (b03=0)
No effect on adjustment (b03=1)
No effect on adjustment (b03=2)
b04
Primary Exchanger type selection (b03=3)
No effect on adjustment (b03=4)
No effect on adjustment (b03=5)
Relay card LC32 operation selection (b02=1)
b05
No effect on adjustment (b02=2)
No effect on adjustment (b02=3)
No effect on adjustment (b02=4)
b06 Mains Voltage Frequency
Comfort burner on time(b02=1)
No effect on adjustment (b02=2)
b07
No effect on adjustment (b02=3)
No effect on adjustment (b02=4)
b08 Driver Gas valve
Notes:
1. Parameters with more than one description vary their function and/or range in relation to the setting of the parameter given in brackets.
2. Parameters with more than one description are reset to the default value if the parameter given in brackets is modified.
To exit the configuration Menu press the DHW buttons together for 10 seconds, or exiting occurs automatically after 2 minutes.

Service menu

The card Service Menu is accessed by pressing the Reset button for 20 seconds. 4 submenus are available: press the Heating buttons to select, in increasing or decreasing order,
"tS", "In", "Hi" or "rE". "tS" means Transparent Parameters Menu, "In" means Information Menu, "Hi" means History Menu: after selecting the submenu, press the Reset button again
to access it; "rE" means History Menu Reset: see description.
"tS" - Transparent Parameters Menu
16 parameters indicated by the letter "P" are available: which are also modifiable from Remote Timer Control.
Press the Heating buttons to scroll the list of parameters in increasing or decreasing order. Press the DHW buttons to view or modify the value of a parameter: the modification will
be automatically saved.
Contents Description
P01 Ignition ramp Offset
P02 Heating ramp
P03 Heating standby time
P04 Heating Post-Circulation
P05 Heating user max. set point
P06 Max. output in heating
Range
0=Natural Gas
1=LPG
1=Bithermal instantaneous
2=Monothermal instantaneous
3=Heating only (3-way valve)
4=Heating only (circulating pump)
0=Sealed Chamber combustion control
(without fume pressure switch)
1=Open Chamber (with fume thermostat)
2=Sealed Chamber (with fume pressure switch)
3=Sealed Chamber combustion control
(with fume thermostat on recuperator)
4=Low-NOx Sealed Chamber (without fume pressure switch)
5=Low-Nox Open Chamber (with fume thermostat)
0=Flat
1=Omega
2=--
--
--
0=Flat
1=Omega
2=--
--
--
0=External gas valve
1=System filling solenoid valve
2=Solar 3-way valve
--
--
--
0=50Hz
1=60Hz
0-20 seconds
--
--
--
0 = Standard, 1
Range
0-40
1-20°C/minute
0-10 minutes
0-20 minutes
31-85°C
0-100%
cod. 3541F151 - Rev. 01 - 03/2018
Default FL 32 MCA
0=Natural Gas 0=Natural Gas
1=Bithermal instantaneous 2=Monothermal instantaneous
0=Sealed Chamber with combustion control 1=Open Chamber (with fume thermostat)
0=Flat 0=Flat
0
0
0=Flat
0
0
0=External gas valve 0=External gas valve
0
0
0
0=50Hz 0=50Hz
5 seconds 5 seconds
5
5
5
0=Standard 0=Standard
Default
20
5°C/minute
2 minutes
6 minutes
80°C
100%
FL 32 MCA
20
5°C/minute
2 minutes
6 minutes
80°C
100%
5
EN