Safety - Metabo KS 216 M Lasercut Instructions D'utilisation Originales

I_0010en5A.fm
Table of Contents
1. Declaration of Conformity .....11
2. Components in the layout
diagram ...................................11
3. Please Read First! ..................11
4. Safety.......................................11
5. Installation and Transport .....13
6. Machine Details ......................13
7. Initial Operation ......................13
8. Operation ................................14
9. Care and Maintenance ...........14
10. Tips and Tricks .......................16
11. Available Accessories ...........16
12. Repair ......................................16
13. Disposal ..................................16
14. Trouble Shooting....................16
15. Technical Data ........................16
1. Declaration of Conformity
We declare in full responsibility that this
product conforms woth the standards
and directives referred to on page 3.
2. Components in the layout
diagram
Figure see page 2.
1 Handle
2 Carrying handle
3 Chip bag
4 Transport locking pin
5 Laser outlet
6 Sawhead tilt lock lever
7 Fence
8 Saw base (table)
9 Table broadening + carrying han-
dle
10 Lock screw for rotating table
11 Stop lever for table extension
12 Rotating table
13 Table insert
14 Work clamp
15 Cutting area illumination
16 Retractable blade guard
17 Saw blade stop
18 Safety lock
19 Saw ON/OFF switch
3. Please Read First!
- Read instructions before use. Pay
special attention to the safety infor-
mation.
- These instructions are intended for
persons with basic technical knowl-
edge regarding the operation of a de-
vice like the one described herein. If
you have no experience whatsoever,
you are strongly advised to seek com-
petent advise and guidance from an
experienced person before operating
this machine.
27.2.11
- Preserve all documents delivered to-
gether with this device. Retain proof
of purchase in case of warranty
claims. If you lend or sell this machine
be sure to have all machine docu-
ments supplied go with it.
- The equipment manufacturer is not li-
able for any damage resulting from
neglect of these operating instruc-
tions.
Information in this manual is denoted
as follows:
A
Danger!
Risk of personal injury or environmental
damage.
B
Risk of electric shock!
Risk of personal injury by electric
shock.
c
Drawing-in/trapping hazard!
Risk of personal injury by body parts or
clothing being drawn into the rotating
saw blade.
A
Caution!
Risk of material damage.
3
Note:
Additional information.
- The numbers in the figures at the be-
ginning of these instructions
- indicate component parts;
- are consecutively numbered;
- relate to the corresponding
number(s) in brackets (1), (2), (3)
... in the text.
- Numbered steps must be carried out
in sequence.
- Instructions which can be carried out
in any sequence are marked with a
bullet (•).
- Listings are indicated by an En Dash
(-).

4. Safety

4.1 Specified conditions of
use
This compound saw (Crosscut saw)
can be used for making rip and cross
cuts, bevel cuts, mitre cuts and com-
pound mitre cuts.
Work only materials suitable for cutting
by the saw blade fitted (see the chapter
on 'Technical Specifications' 
for available saw blades).
The permissible dimensions of the
workpieces must be adhered to (see
the chapter on 'Technical Specifica-
tions).
Original operating instructions
Stock having a round or irregular cross
section (such as firewood) must not be
cut as it cannot be securely held during
cutting. When sawing thin stock layed
on edge, a suitable auxiliary fence must
be used for firm support.
Any use other than the use specified
above is not allowed. Unspecified use,
modifications to the machine, or use of
parts not tested and approved by the
equipment manufacturer may cause
unforeseeable damage!
4.2 General Safety
When using this machine observe the

following safety instructions, to mini-
mize the risk of personal injury or ma-
terial damage.
Please also observe the special safe-

ty instructions in the respective sec-
tions.
Where applicable, follow the legal di-

rectives or regulations for the preven-
tion of accidents pertaining to the use
of crosscut saws.
A
Keep your work area tidy - a messy

work area invites accidents. Keep the
floor clean from loose particles as
chips and cuttings.
Be alert. Know what you are doing.

Set out to work with reason. Do not
operate tool while under the influence
of drugs, alcohol or medication.
Consider environmental conditions.

Sorgen Sie für gute Beleuchtung des
Arbeitsbereichs.
Prevent adverse body positions. En-

sure firm footing and keep your bal-
ance at all times.
Do not operate the machine near in-

flammable liquids or gases.
This tool may only be started and op-

erated by persons familiar with cross-
cut saws and who are aware of the
dangers associated with the operation
of such tools. 
Persons under 18 years of age shall
use this device only in the course of
their vocational training, under the su-
pervision of an instructor.
Do not let other persons, especially

children touch the tool or the cable.
Keep them away from the workung
area.
Do not overload device - use it only

within the performance range it was
designed for (see "Technical Specifi-
cations").
Use the correct electric tool.Do not

use inefficient machines for heavy du-
ties. Do not apply electric tools for
purposes they are not intended for.
Do for instance not use a circular
hand saw for cutting tree branches or
logs.
ENGLISH
Instructions
General hazards!
11