Bosch GSR ProDrive Professional Notice Originale page 12

OBJ_BUCH-747-003.book Page 12 Monday, October 10, 2011 8:28 AM
12 | English
Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
Use only original Bosch batteries with the voltage list-
ed on the nameplate of your power tool. When using oth-
er batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for driving in and loosening screws.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Screwdriver bit*
2 Tool holder
3 Battery unlocking button*
4 Battery*
5 On/Off switch
6 Rotational direction switch
7 "PowerLight"
8 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Screwdriver
Article number
Rated voltage
No-load speed
Max. torque for hard/soft screw-
driving application according to
ISO 5393
Max. screw dia.
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
1 609 929 R40 | (10.10.11)
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
determined according to EN 60745:
Screwdriving without impact: a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
GSR ProDrive
Professional
3 601 JA2 0..
V= 3.6
Robert Bosch GmbH, Power Tools Division
-1
min 0 – 250
D-70745 Leinfelden-Echterdingen
04.10.2011
Assembly
Nm 7/3
mm 5
Battery Charging (see figure A)
Use only the battery chargers listed on the accessories
kg 0.5
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
(triax vector sum) and uncertainty K
h
2 2
<2.5 m/s , K=1.5 m/s
h
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
Bosch Power Tools
.