Refsta BOREA PLUS Notice D'utilisation page 22

ance's control panel (Fig. 2.1).
Drill 5 Ø8 holes in the ceiling and tighten 3 screws E without
tightening them completely making sure that the screws are
not inserted in the holes marked with an X on the drill hole
template (the screws and anchors must be suitable for the
type of wall).
- Take structure B (Fig. 2.2) and insert it on the 3 screws that
have not been tightened completely, in correspondence of
the 3 slots.
Make a small rotation to lock it in (Fig. 2.2).
- Tighten the fourth and the fifth screw X and the 3 remain-
ing one to lock structure B into its final position.
To adjust cable height it is necessary to refer to the lengths
shown in (Fig. 3.1)
- To adjust the cable, first loosen the 2 screws A of the del
clamp as shown in figure 3.2 (X).
- Once the length of the cable has been adjusted, tighten
the 2 screws A as shown in figure 3.2 (Y).
- Couple the hood body C and the structure B in correspond-
ence of the 4 slots F and the four screws G (not completely
tightened) figure 4 - phase 1.
- Rest the hood body on the 4 slots figure 4 - phase 2
- Tighten the 4 screws G and fasten the structure perma-
nently B to the hood C with the 4 safety screws H figure 4
- phase 3.
- Using a level align the hood by turning the adjustment
screws R as shown in figure 5.
- Once the hood is aligned, in order to lock the adjustment
screws permanently R, tighten the nut D as shown in fig. 5.
- Before completing the electrical connection, fasten the
box S to the bracket using the 2 screws D figure 6 - phase 1.
- Open the box lid S removing the adhesive tape.
- Connect to the electrical network as shown in figure 6 -
phase 2.
- Close the lid of the box S figure 6 - phase 3, and fasten with
the two screws E figure 6 - phase 4
- Take the aesthetic frame C and using the 2 screws A fasten
it to the structure B fig. 7.
Attention! Based on the model that has been purchased,
the product may be equipped with COURTESY LIGHTS OP-
TIONAL, before fastening the small cupola to the hood body
connect the lights as shown in figure 8.
- Pass the power supply cable through the slots of the small
cupola as shown in figure 9.
- Take the small cupola and fasten it to the hood using the 8
screws G as shown in figure 9.
- If your model is like the one shown in figure 10 it is nec-
essary to fasten the decorative cover M1 - M2.
- In correspondence with the hood body there are 4
(right)+ 4 (left) screws X that are not completely tight-
ened figure 10 - phase 1, take the decorative cover M2
and slide it down until it clamps onto the slot phase 2-3-
4-5.
- Take a spanner that is suitable for the screws X and
tighten them to fasten the decorative cover perma-
nently M2.
- Repeat the same operation for the M1 cover.
• Filtering version
- Before proceeding with the replacement of the regen-
erative filter, open the aesthetic panel.
- Remove the aluminium panel by pulling the handle as
shown in fig. 11.
- Remove the brackets from their housing and pull them
outwards. (Fig. 12).
Unlike traditional carbon filters, this carbon filter can be
washed and reactivated for approximately 12-15 times.
With normal hood use, this filter should be cleaned once
every 2-3 months. The filter can be washed into a dishwasher
at the highest temperature using a standard dishwasher
detergent.
After washing, dry the filter in the oven at 100° C for 10-15
minutes to reactivate it.
The filter will retain its odour-absorbing capacity for three
years, after which it will have to be replaced.
USE AND MAINTENANCE
• We recommend that the cooker hood is switched on before
any food is cooked.
We also recommend that the appliance is left running for
15 minutes after the food is cooked, in order to thoroughly
eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
• The anti-grease filter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the filter to become saturated depends on
the way in which the appliance is used).
- To prevent potential fire hazards, the anti-grease filters should
be washed a minimum of every 2 months (it is possible to use
the dishwasher for this task).
- After a few washes, the colour of the filters may change. This
does not mean they have to be replaced.
If the replacement and washing instructions are not followed,
the anti-grease filters may present a fire hazard.
• The active carbon filters are used to purify the air which is
released back into the room.
The active carbon filter saturation level depends on the fre-
quency with which the appliance is used, the type of cooking
performed and the regularity with which the anti-grease
filters are cleaned.
• Clean the cooker hood frequently, both inside and outside,
using a cloth which has been dampened with denatured
alcohol or neutral, non-abrasive liquid detergents.
ATTENTION!
Before proceeding with the replacement of halogen lights it
is necessary to open the aesthetic panel figure 13 - phase 1;
loosen the two screws F lift the small panel G as shown in fig-
ure 13 - phase 2-3.
• Replacing halogen light bulbs (Fig. 13 - phaset 4).
To replace the halogen light bulbs B, remove the glass pane
C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
Optional !
As an optional the product may be equipped with side halo- optional the product may be equipped with side halo- the product may be equipped with side halo-
gen lamps figure 14.
To replace them, it is necessary to remove the decorative
cover M1 or M2 and repeat the same operations shown in
fig. 13 - phase 4 "Replacing halogen lamps".
• Commands: (Fig.15)
NOTE: With this control it is possible to manage the appliance
also with a remote control to be requested as accessory.
Power Button (A) = the on / off button switches on and off
the whole hood (motor and lights).
By pressing the button the motor starts at 1st speed.
Fan Speed button (B) = From the OFF position, press once
for the 1st speed, twice for the 2nd speed and three times
- 22 -