Publicité
- The switch is on.
- The appliance is powered. Check that the domestic power
supply is working by testing other electrical household
appliances which you know are operating correctly.
In case the heater overheats, the safety sensor will
automatically stop the heater even if the timer is on.
Find out for what reason the heater overheated. The reason for
this could be too tightly placed sauna stones, heater´s location
or inappropriate ventilation. If this occurs, fi nd out the cause
and fi x the problem before resetting the safety sensor.
The reset button is located below the temperature knob.
If the above operations do not solve the problem, contact your
nearest service centre or the company.
HANDLING
If it is necessary to move the sauna to another location,
even inside the same room, it must be dismantled and then
reassembled where required, once again following the assembly
instructions given in this manual.
NEVER ATTEMPT TO LIFT THE FULLY ASSEMBLED SAUNA
EITHER BY HAND OR WITH ANY AVAILABLE EQUIPMENT.
Fill the stove with the stones provided.
The stones that are provided have already been washed, however
we recommend washing them again before inserting them inside
the heat generator.
The smallest stones must be placed in the bottom of the frame
and the largest ones on the surface. The stones must not be
placed too near each other, as it is important to guarantee correct
circulation of air. The stones must also be inserted one on top
of the other without completely covering the heating elements
of the stove.
We recommend re-positioning the stones at least once a year
although preferably twice a year, at which time the smallest stones
and any that are broken will be discarded.
This is done to ensure correct air circulation inside the stove and
to avoid overheating of the heating elements and consequent
failure. The stones must be sized 3-5 cm.
CAUTION: lack of ventilation through the stones positioned
inside the stove can cause malfunction of the heating
elements.
WARNING FIRE HAZARD: do not pour essential oil
concentrates onto the stove without diluting it with lots of
water, APPROX. 3 DROPS FOR EVERY litre OF WATER. DO
NOT HEAT WITHOUT STONES.
FIRST TIME OF SWITCHING ON
CAUTION: qualified personnel only must carry out the
preliminary checks and make any adjustments to the
installation.
STOVE
Switch on the product by putting the installation master
switch to on.
Check the sauna functions.
It is recommended not to exceed 15-20 minutes in the sauna
at a time, remaining for shorter times at the beginning to avoid
alterations to blood pressure.
After the sauna it is usual to take a cold shower to bring body
temperature back to a normal level and to have a fi rming effect
on the skin.
In order to use the sauna one must start the stove at least
1 hour before it is actually used. Make sure that there is no
fl ammable material inside the stove or objects resting on it
before switching on.
WHEN USING THE SAUNA FOR THE FIRST FEW TIMES,
STEAM COULD CONDENSATE ON THE INTERNAL SURFACE
OF THE GLASS DUE TO THE MOISTURE IN THE WOOD. THIS
TEMPORARY EFFECT OF CONDENSATION WILL STOP IN
A VERY SHORT TIME.
DO NOT REST ANYTHING ON TOP OF THE SAUNA STOVE
TO AVOID THE RISK OF FIRE.
After using the sauna it is a good rule to let it cool down by leaving
the door open. It is also advisable to ventilate the room where
the sauna is installed.
STOVE OPERATION
THERMOSTAT
Adjust the temperature of the sauna by simply turning the
operating knob.
Thermostat support automatically the choosen temperature.
TIMER
To start the heater at once, turn the knob to anywhere between
1-4 on the operating time scale.The heater will start and remain
on for the time selected.
To preset the delayed start Timer, simply turn the knob to
anywhere between 1-6. When the specifi c number of hours is
reached, the heater will start running and stay on for up to 4 hours
if you don´t turn it off earlier.
13
SAUNA
Delayed start Timer stove
from 1 to 6 hours.
ON/OFF Stove
Stove operating time
from 1 to 4 hours.
EN
Publicité
