Start Up - Fhiaba Brilliance Série Notice D'installation

3
Before starting
3.4 Electronic Control
The innovative electronic control system designed by Fhiaba maintains constant temperature in multiple compartments and
displays it on the control panel. It also allows user interaction making it possible to personalize settings of various functions and
to alert the user with sound and/or visual messages should any malfunction occur in the appliance.
Main control panel 3.5
11
12
1 2 3 4 5 6 7 8 9
Switches the appliance (all compartments) between ON and STAND BY
1 Unit
(press for three seconds).
13
Allows switching on and off of only the refrigerator compartment
2 Fridge
(press for three seconds).
3 Menu
Allows access to the appliance function menu
Up/down
Using the Up and Down buttons, it is possible to change the set tempera-
4
Fridge
ture of the refrigerator and navigate through the interactive menu.
It shows the temperature of the refrigerator and freezer compartments,
5 Display
the date and time, Menu functions and visual messages.
Up/Down
By selecting Up/Down the preset temperature can be changed accord-
6 Freezer
ing to the selected function mode (freezer, refrigerator, Crisper-Fresco).
(TriMode)
Confirms activation or deactivation of the selections made in the
7 Enter
Menu.
8 Ice maker Allows activating or deactivating the automatic ice production.
Blinks to signal user alerts such as door left open, also in combination with
9 Alarm
a sound signal which can be deactivated by pressing the button.
8
www.fhiaba.com www.thevettagroup.com
If at the first start - up the message Stand by
does not appear, but other messages appear,
such as Fridge too warm, Fresco too warm,
Freezer too warm, or sound signals are activat-
ed, it means, it means that the appliance has
already started the cooling process.
If this is the case, deactivate any possible acous-
tic signals by pressing the Alarm button, close
the door and wait until the set temperature is
reached.
It is necessary to let the unit reach the correct
temperature before foods are stored inside.
To start the appliance, connect the plug to the electrical mains: at
this point, when opening the door, the control panel will usually visual-
ize the message "Stand by", and all the panel keys be off
To turn on all the appliance compartments, press the Unit
for three seconds. The display will show the message "Initial test" for
approx. 2 minutes. After this phase the compressors will start up and re-
main on until the default temperature set up in the factory is reached.
Do bear in mind that this condition could last several hours during
which time the display will continue to flash the 'Start Up Phase' mes-
sage.
3
Before starting
Crisper-Fresco control panel 3.6
If the appliance is provided with an Ice Maker, prior to switching it on
10 11 12
make sure that the water filter cartridge is installed (unless water sup-
Display
Shows the temperature of the Crisper-Fresco compartment.
Up/Down Using the Up and Down buttons, it is possible to change the
temperature set for the Crisper-Fresco compartment. ply source is already filtered by other means such as reverse osmosis).
Allows switching on and off of only the Crisper-Fresco compartment
Crisper (press
for three seconds).
Purge air from the water lines by enacting the 'Manual Clean' func-
tion from the Menu->Functions->Water Filter options. You may need to
complete this sequence several times until you stop hearing air sput-
tering from the ice maker fill tube.
Once you are satisfied that the system is purged of air switch the Ice
Maker on by touching the
9
www.fhiaba.com www.thevettagroup.com
Note: If the TriMode drawer is configured as a Fridge or a Fresco com-
partment the ice maker will be disabled. Default mode for the TriMode
drawer is Freezer.
For further information about the appliance operation, refer to the
User Manual.
Installation Guide
button which will illuminate.
www.fhiaba.com · www.thevettagroup.com
Series: All

Start up

button
25