Publicité
Les langues disponibles
Les langues disponibles
Initial Setup
en
The three-phase sensor setting allows the adjustment of channel, operating
mode and tolerance values.
● = Button pressed
■ = LED on
Detection
– Place object to detect inside the operating distance, in front of the sensor.
OUT
OR
1
2
3
– Press the SET button for at least two seconds.
– The "Set1" message is visualized.
Channel Setting
OR
1
2
3
– Use the SEL button to select the channel of detection.
OR
1
2
3
Operating mode
– Place the SET button again to confi gure operating mode.
– Select C (color) or C+I (color + intensity) using the SEL button.
– Note: The "C" type algorithm is used to obtain a larger depth of field, or to
detect colors on different opaque, shiny or reflecting surfaces. Whereas
the "C+I" type algorithm offers a higher sensitivity toward tone variations
and is recommended for the detection of different colors on the same type
of material, with the possibility of also distinguishing the gray tones.
OR
1
2
3
Teach and Tolerance Settings
– Press the SET button again, the "updt" text blinks for two seconds.
– The sensor then automatically passes into the tolerance section.
– Use the SEL button to select the required value.
OUT
OR
1
2
3
OR
1
2
3
– The "FAIL" text alternated with "Hi" or "Lo" is visualized
if the detection is not correct.
– Repeat the procedure starting from the Operating Mode.
￫
The 0, 1 and 2 tolerance values are particularly suitable for
critical applications.
4/17
○ = Button not pressed
□ = LED off
Display
Keyboard
Dig1
Dig2
Dig3
Dig4
SET
SEL
r
u
n
d
Dig1
Dig2
Dig3
Dig4
SET
SEL
S
E
t
1
Dig1
Dig2
Dig3
Dig4
SET
SEL
S
E
t
1
S
E
t
2
S
E
t
3
Dig1
Dig2
Dig3
Dig4
SET
SEL
C
C
_
I
Display
Keyboard
Dig1
Dig2
Dig3
Dig4
SET
SEL
u
p
d
t
Dig1
Dig2
Dig3
Dig4
SET
SEL
t
o
L
0
t
o
L
1
t
o
L
2
t
o
L
...
t
o
L
9
Setting parameters
Delay Value Visualizing and Setting
OUT
OR
1
2
3
Dig1
Dig2
r
– Press the SET button for at least six seconds to access the delay setting mode.
OR
1
2
3
Dig1
Dig2
d
d
d
d
d
d
Notes on Setting Delay
At each press of the SET button, the different delay levels in milliseconds are
shown in a cyclical manner, and the delay value will be stored. The delay
value setting is common for all three outputs. When a delay value other than
zero is set, the outputs will be maintained active for a minimum time equal to
the number of milliseconds visualized on the display
(i.e. d-00 = 0 ms, d-05 = 5 ms, d-10 = 10 ms).
Channel Status Visualization
This function provides adjustment for all three sensor channels.
Press the SEL button for at least two seconds and channel, operating mode
and tolerance are shown sequentially.
OUT
OR
1
2
3
Dig1
Dig2
r
OR
1
2
3
Dig1
Dig2
C
C
t
C
C
t
C
C
t
d
OR
1
2
3
Dig1
Dig2
r
– At the end of the sequence, the display will indicate the "run" or "rund"
operating mode again.
Non-Initializing E2PROM
If the display indicates "E2Pr" the sensor does not have any of the three
channels initialized.
OUT
OR
1
2
3
Dig1
Dig2
E
– In this case, it is sufficient to program one single channel to obtain the
"run" or "rund" visualization on the display.
Display
Keyboard
Dig3
Dig4
SET
SEL
u
n
d
Dig3
Dig4
SET
SEL
-
0
0
-
0
5
-
1
0
-
2
0
-
3
0
-
4
0
Display
Keyboard
Dig3
Dig4
SET
SEL
u
n
d
Dig3
Dig4
SET
SEL
h
_
1
_
I
o
L
2
h
_
2
o
L
1
h
_
3
o
L
8
-
0
5
Dig3
Dig4
SET
SEL
u
n
d
Display
Keyboard
Dig3
Dig4
SET
SEL
2
P
r
Publicité
