Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE
•
Wear eye protection.
• Use splash hood for every operation for which it can be used.
• Unplug saw before servicing, when changing cutting blades, and cleaning.
• Use tool only with smooth-edge cutting wheels free of openings and grooves.
• Replace damaged cutting wheel before operating.
• Do not fill water tray above water fill line.
• Do not expose to rain, or use in damp locations.
USE PROPER EXTENSION CORD. Make
cord, be sure to use a cord heavy enough to carry the current your product will draw. An undersized cord will cause
a drop in line voltage, resulting in loss of power and overheating. Table below shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
Ampere Rating
More Than
0
6
10
12
STATE-OF-THE-ART FEATURES
•
Powerful 2-HP motor.
• Rip cut up to 24" square tiles and diagonal cut up
to 17" tiles.
• Cutting table designed with slide tube mount, for
precise "wobble-free" travel.
• The adjustable rip guide allows both 90° and 45°
cuts. Universal wrench included.
• Quick and easy blade "truing".
• Blade shaft lock for easy blade changes.
• Fiberglass-impregnated plastic water tray
withstands even the toughest punishment. Easy to
remove and install.
• Carrying handles for easy transporting. Optional
saw stand on wheels provides simple, one-man
moving.
• Automatic power kill switch shuts off motor if
power is interrupted. Easy ON/OFF toggle switch.
UNPACKING, ASSEMBLY & SETUP
CAUTION: FOLLOW ALL OF THE
THE SAW TO A POWER SOURCE OR TURNING THE MOTOR ON.
Carefully open the container and remove all saw components and packing materials. Ensure that you have
checked each item with the exploded view on page 11 before discarding the container or packing materials. The
contents of the container are as follows:
• Motor Assembly
• Saw Frame
• Fiberglass-Impregnated
• Plastic Water Tray
Carefully lift the saw by the saw frame handles and place it on a flat, level working area or on the stand on wheels.
The following pages illustrate step by step the installation of various components and operation of the saw. Read
instructions completely before operating this saw!
sure your extension cord is in good condition. When using an extension
Volts
120V
240V
Not More Than
6
10
12
16
ASSEMBLY & INSTALLATION INSTRUCTIONS COMPLETELY BEFORE CONNECTING
• 45°/90° Rip Guide
• Universal Wrench
• Owner's Manual
• 10" Diamond Blade
OPERATING SAW.
TABLE 1
Total length of cord in feet
25ft.
50ft.
50ft.
100ft.
AWG
18
16
18
16
16
16
14
12
•
Easily converts from a stand on wheels to a tabletop
configuration.
• Automatic thermal overload protection protects saw
from power surges and motor overheating.
ELECTRICAL/MOTOR
• Horsepower
2 HP
• Volts
115V, 60Hz
• Amps
15
• RPM
3600 (single speed)
• Connect saw as close as possible to power source.
• Belt
A-26
EXTENSION CORDS: When using an extension
ensure all cords are no smaller than #12 gauge, rated at
a 20-amp minimum, and equipped with 3-prong plugs.
Use of anything smaller may result in overheating or
burn out of the motor. It is recommended that an
electrician ensure that there is proper voltage at the saw
motor to run the saw efficiently and safely.
• Drain Plug
• Front Extension Table
• Miter Block
-
5 -
100ft.
150ft.
200ft.
300ft.
16
14
14
12
14
12
Not Recommended
SPECIFICATIONS
• Water Pump
• Side Extension Table
• Heavy Duty Stand
cord,
Publicité
Table des Matières
