Additional Information; Troubleshooting; About The Exemption Clauses - Pioneer DJM-5000 Mode D'emploi

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes
the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the
items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by unplugging the power
cord then plugging it back in.
Problem
The power is not turned on.
No sound or small sound.
Distorted sound.
Can't crossfade.
Can't fader start a DJ player.
No effect.
Can't use an external effector.
Distorted sound from an external effector.
This unit is not recognized after it has been connected
to a computer.

About the exemption clauses

! Pioneer is a registered trademark of Pioneer Corporation.
® ®
! Microsoft
, Windows Vista , and Windows
or trademarks of Microsoft Corporation in the United States and/ or other
countries.
! Pentium is a registered trademark of Intel Corporation.
! Adobe and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/ or other countries.
! Apple, Macintosh or Mac OS are registered trademarks of Apple Inc. in the
United States and/ or other countries.
! ASIO is a trademark of Steinberg Media Technologies GmbH.
! The names of companies and products mentioned herein are the trademarks of
their respective owners.
This product has been licensed for nonprofit use. This product has not been
licensed for commercial purposes (for profit-making use), such as broadcast-
ing (terrestrial, satellite, cable or other types of broadcasting), streaming on
the Internet, Intranet (a corporate network) or other types of networks or dis-
tributing of electronic information (online digital music distribution service).
You need to acquire the corresponding licenses for such uses. For details, visit
http:/ / www.mp3licensing.com.
The audio compression technology for MP3 is offered under the license of
Fraunhofer IIS and Thomson Multimedia.
Check
Is the power cord properly connected?
Is the position of the input selector switch properly set?
Are the connection cables properly connected?
Are the terminals and plugs dirty?
Is [MASTER ATT] on the rear panel set to a level like -12 dB?
Is the level of audio output from the microphone channel
properly set?
Is the level of audio input to each channel properly set?
Is the crossfader assign switch properly set?
Is [FADER START] set to off?
Is the DJ player properly connected to the [CONTROL]
terminal?
Are the audio cables properly connected?
Is [EFFECT] set to a proper position?
Is [SEND/ RETURN] [ON/ OFF] set to on?
Is the external effector properly connected to the [SEND]
or [RETURN] terminal?
Is the output channel switch of [SEND/ RETURN] properly
set?
Is the level of audio input from the external effector prop-
erly set?
Is the driver software properly installed on your computer?
®
are registered trademarks
Remedy
Plug in the power cord to an AC outlet.
Switch the input source of a channel with the input selector switch (page
13).
Connect the connection cables properly (page 8).
Clean the terminals and plugs before making connections.
Switch [MASTER ATT] (page 7).
Adjust the [LEVEL] dial for [MASTER] so that the master channel level
indicator lights at about 0 dB at the peak level (page 13).
Set [MASTER ATT] to [-6 dB] or [-12 dB] (page 7).
Adjust the [TRIM] control such that the channel level indicator lights up
near 0 dB at the peak level (page 13).
Set the crossfader assign switch properly for each channel (page 13).
Set [FADER START] to on (page 14).
Connect a DJ player to the [CONTROL] terminal with a control cord (page 8).
Connect this unit to the audio output terminal of a DJ player with an audio
cable (page 8).
Set [EFFECT] to a position other than [LOW] (page 13).
Press [ON/ OFF] of [SEND/ RETURN] to turn on [SEND/ RETURN] (page 13).
Connect an external effector to the [SEND] or [RETURN] terminal. When the
connection is made properly, [ON/ OFF] of [SEND/ RETURN] lights up in red
(page 8).
Switch the output channel with the output channel selector switch(page 13).
Turn the [LEVEL] dial for [SEND/ RETURN] to adjust the audio level output
from the external effector (page 13).
Install the driver software. Reinstall it if the driver software has already been
installed (page 9).
Unless this unit is properly connected to the computer and there is no error
in data transmission, the version display utility program cannot display the
firmware of this unit. For details of how to check, see Checking the version of
the driver software on page 11.
17
En