Publicité
Les langues disponibles
Les langues disponibles
MODE SETTINGS
Max Speed - Select the max RPM to be reached
when running the tool in forward.
Bolt Removal - Select the max RPM to be reached
when running the tool in reverse.
Precision Mode - Enable or disable, and set the
limit on the torque output of the tool. For maximum
torque output, set the Precision Mode to OFF. To
control the torque, set the Precision mode to ON
and select the level. For lower torque applications
select lower levels, and for higher torque applications,
select higher levels. For torque-specific applications,
confirm the final tightening torque with a calibrated
torque wrench.
Trigger Ramp-Up - Set the length of time it takes for
the tool to reach full speed.
Torque Level (Estimate) (2869-20 only) - Review
the torque range (350-450 ft-lbs). For precision ap-
plications, confirm the final tightening torque with a
calibrated device.
Star Patterns (2869-20 only) - Review the star pat-
terns for bolt installation/removal.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Using the MODE Selector
Mode Selector Button
Mode Indicators
The mode selector button
mode set in the ONE-KEY™ app.
To select the mode:
1. Pull and release the trigger to turn on the tool. The
current mode indicator is lit.
2. Press the mode selector button
the 4 modes. When the desired mode indicator is
lit, begin work.
3. The ONE-KEY™ Indicator lights, to indicate the
following:
ONE-KEY™ Indicator
is used to select the
to cycle through
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock.
1. For forward (clockwise)
rotation, push the con-
trol switch in the direc-
tion shown. Check the
direction of rotation
before use.
2. For reverse (counter-
clockwise) rotation,
push the control switch
in the direction shown.
Check the direction of
rotation before use.
3. To lock the trigger, push
the control switch to the
center position. The tool
will not run when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1. To start the tool, pull the trigger.
NOTE: An LED is turned on when the trigger is pulled.
2. To vary the driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed, up to the max RPM
set by the MODE.
3. To stop the tool, release the trigger.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight, reduce the impacting time. If they are
not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the
head of the fastener affects the degree of tightness.
The torque required to loosen a fastener averages
75% to 80% of the tightening torque, depending on
the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a
relatively light torque and use a hand torque wrench
for final tightening.
5
Push for
reverse
Push
to
center
to lock
Push for
forward
Publicité
