Cardin Elettronica HL Série Mode D'emploi page 11

IMPORTANT REMARkS
READ THE FOLLOWING REMARkS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLA-
TION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARkED WITH THE SYMBOL
NOT READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORk-
ING ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALLERS
OF ELECTRICAL EQUIPMENT" and must respect the local standards
and regulations in force. All materials used must be approved and must
suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians. Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it has
been made. "i.e. for the automation of one or two hinged gates".
The appliance may be used to operate hinged gates and doors, with gate
leaves up to 3 m in length and the following characteristics:
- maximum weight for 2-3 m long gates = 550 kg
- maximum weight for gates less than 2 m long = 700 kg
• The unit may be fitted both to the right and to the left of the passage-
way.
• This product and all its relative components has been designed and
manufactured by Cardin Elettronica who have verified that the product
conforms in every aspect to the safety standards in force.
Any non authorised modifications are to be considered improper and
therefore dangerous.
The manufacturer accepts no liability for situations arising from the use
of an electrical installation which does not conform to the local standards
and regulations in force and in particular when the earthing circuit is not
efficient.
IMPORTANT SAFETY INSTRUCTIONS
It is the responsibility of the installer to make sure that the following public
safety conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the
main road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property
and not on the public side of the gate. The gates must not
swing outwards onto a public area.
3) The gate operator is designed for use on gates through
which vehicles are passing. Pedestrians should use a
separate entrance.
4) The gate must be in full view when it is operating therefore
controls must be situated in a position where the operator
can see the gate at all times.
5) At least two warning signs (similar to the example on the right) should be
placed, where they can be easily seen by the public, in the area of the
system of automatic operation. One inside the property and one on the
public side of the installation.
These signs must be indelible and not hidden by any objects (such as
tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children and/or pets must not
be allowed to play within the area of a gate installation. If possible include
this in the warning signs.
7) Whenever a fully open gate leaf comes within at least 500 mm of a fixed
structure the space must be protected by an anticrush buffer.
8) A correct earth connection is fundamental in order to guarantee the
electrical safety of the machine
9) If you have any questions about the safety of the gate operating system,
do not install the operator. Contact your dealer for assistance.
TECHNICAL DESCRIPTION
800/HL251CL Reversible geared motor, maximum opening 110°.
806/HLCF1
Embedding case in zinc plated steel with cataphoresis
finishing and a transmission lever for 110°.
806/HLCF1Z Embedding case in zinc plated steel with transmission
lever for 110°.
800/HL2518CL Reversible geared motor, gate opening 118°-360°.
806/HLCF18
Embedding case in zinc-plated steel with cataphoresis
finishing and accessories for gate opening 110°-360°.
806/HLCF18Z Embedding case in zinc-plated steel with accessories for
gate opening 110°-360°.
806/HLCA140 Kit of lever accessories for a 140° opening angle.
IMPORTANT REMARkS
• Single piece geared reduction unit;
- Single phase drive motor with an incorporated overload protector and a
permanently lubricated reversible reduction unit mounted on a cast iron
stator.
- Rubber sealing gasket;
- Key operated manual release mechanism.
• Embedding case in hot rolled zinc-plated steel;
- Release unit housing in pressed aluminium.
• Transmission levers in zinc-plated steel;
- Gate fastening bracket in zinc-plated steel.
USER INSTRUCTIONS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has
expired it must be disposed of separately from other rubbish.
The user is therefore obliged to either take the product to a
suitable differential collection site for electronic and electrical
goods or to send it back to the manufacturer if the intention
is to replace it with a new equivalent version of the same
product.
Suitable differential collection, environmental friendly treatment and
disposal contributes to avoiding negative effects on the ambient and
consequently health as well as favouring the recycling of materials.
Illicitly disposing of this product by the owner is punishable by law and
will be dealt with according to the laws and standards of the individual
member nation.
During the opening/closing manoeuvre check for correct operation and
activate the emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred using
the supplied release key (see manual release).
Periodically check the moving parts for wear and tear and grease if required,
using lubricants which maintain their friction levels unaltered throughout time
WARNING
AUTOMATIC OPENING and are suitable for temperatures of -20 to +70°C (in particular the release
KEEP CLEAR
lever which is fitted with a greaser "J" fig. 9). In case of failure or operational
anomalies switch off the power at the mains do not attempt to repair the
appliance yourself. Periodically check the correct operation of all safety
devices (photoelectric cells etc.) Eventual repair work must be carried out
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
by specialised personnel using original spare parts.
NEAR THE INSTALLATION
INSTALLATION INSTRUCTIONS
The minimum controls which may be installed are OPEN-STOP-CLOSE,
these controls must be installed in a location not accessible to children.
Before starting with the installation of the system check that the structure
which is to be automated is in good working order and respects the local
standards and regulations in force.
To this end make sure that the gate is sufficiently rigid (if necessary reinforce
the structure) and that the hinges turn easily.
You are advised to grease all the moving parts using lubricants which maintain
unaltered friction characteristics over a period of time and are suitable for
temperatures of -20 to +70°C.
The appliance is not suitable for continuous operation and must be contained
within the value stipulated (see technical data on page 20).
• Check the safety measures between the fixed and moving parts:
- a minimum space of 30 mm must always be left along the entire distance
between the gate and the support column measured throughout the
entire opening angle of the gate.
- make sure that the space between the bottom of the gate and the
pavement never exceeds 30 mm throughout the entire opening angle
of the gate.
• The surface of the gate must not feature openings which allow a person's
hand or foot to pass through.
• Check the exact positioning of the pivots and hinges, and their good
working order (the upper and lower hinges/pivots must be aligned on the
same axis).
• Work out the run of the cables according to the command and control
devices fitted and make sure the system conforms to the local standard
and regulations in force (see installation example fig.1 pag. 2).
11
11
IMPORTANT REMARkS