Servicing - Falcon Classic Deluxe 110 Ceramic Mode D'emploi / Instructions D'installation & D'entretien

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.

Servicing

Disconnect the cooker from the electricity supply before
commencing servicing, particularly before removing any
of the following: control panel, side panels, ceramic hob,
or any of the electrical components or cover boxes.
Prior to reconnection, check that the appliance is
electrically safe.
1 To Remove the control panel
Disconnect from electricity supply.
Pull off all the control knobs.
Open the grill and right hand oven doors and remove the
three fixing screws underneath the control panel.
The control panel should drop down slightly. It is held at the
top by two holes in the top edge, one at each end, that locate
on tags on the inner panel.
Clear the control panel holes from the inner panel and pull
the control panel forward.
Disconnect the wiring from the rear.
Reassemble in reverse order. When replacing leads, refer to
the wiring diagram in this manual. Check the operation of the
timer.
2. To Remove a Side Panel
Disconnect from electricity supply.
Remove the control panel (see section 1). Pull the cooker
forward. Remove the four retaining screws for each panel
(one at the front base, one on the top, and two at the rear).
Reassemble in reverse order.
3. To Lift up the Ceramic Hob
Disconnect from electricity supply.
Pull the cooker forward. Unscrew the two screws which are
located at the rear of either side of the cooker underneath the
grill trim. Push the hob backwards to release the front catchment
bracket. Lift the hob.
Hold the hob in place using the rod attached to the underside
of the hob, by locating the loose end into the central hole in the
top of the inner control panel.
Caution
The ceramic hob material is much more sensitive to
scratches on the underside than the top.
Take care not to touch or scratch the underside of the
ceramic as this will weaken the material and cause the top
to shatter.
4. To replace a Hob Element
Disconnect from electricity supply.
Lift up ceramic hob see 3. The elements are now accessible. Note
the wire connection positions and element orientation for re-
assembly. Disconnect wires, unscrew centre screw and carefully
remove element with spring. Unscrew the two screws to remove
the spring. Re-assemble in reverse order, using the same screws.
Note: Orientation of element is important. Use the numbers on
the back of the element to ensure correct relocation of spring.
5. To Replace the Light Switch
Disconnect from electricity supply.
Remove the control panel (see section 1).
NB. The old switch may be destroyed during removal. Remove
the old switch from its bezel by gripping the switch body
behind the control panel and twisting sharply. The switch
bezel can then be removed by folding back its locking wings
and pushing forward. Fit the new bezel to the control panel
by first lining up the raised key on its body with the cutout in
the control panel and pushing it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the Control Panel in reverse order and test for correct
operation.
6. To Remove the Electronic Timer
Disconnect from electricity supply.
Remove the control panel (see section 1). Pull off the timer
control button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fixing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling
the unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram in this manual. Check the operation of
the timer.
7. To Replace a Thermostat
Disconnect from the electricity supply.
Remove control panel (see section 1) and lift hob (see section
3). Open the oven door. Remove the oven furniture and slide
out the oven roof liner if fitted.
For the RH oven, remove the thermostat phial cover (two
screws). Unclip the thermostat phial from the clips in the
oven back.
For the LH oven, pull cooker forward to gain access to the
cover box at the rear of the cooker. Remove the four screws
securing the cover and lift clear.
Feed the thermostat capillary out of the oven. Disconnect
the wiring from the thermostat. Remove two screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned between
the clips.
19