EINHELL TC-CS 860/1 Kit Mode D'emploi D'origine page 20

5.2 Extraction of dust and chips (Figure 3)
Connect your tool to an extraction unit or vacuum
cleaner. This will provide excellent extraction of
chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
•
Attach the adapter for the dust extraction
system (11) to the connection for the dust ext-
raction system (10).
•
You can then connect a suitable vacuum
cleaner (not supplied) to the dust extraction
system adapter (11).
5.3 Parallel stop (Figure 4/5)
•
The parallel stop (9) enables you to saw par-
allel lines.
•
Loosen the locking screw for the parallel stop
(8) on the saw foot (6).
•
To assemble, slide the parallel stop (9) into
the guide (a) on the saw foot (6) (see Figure
4).
•
Set the required spacing and then tighten the
locking screw (8) again.
•
Using the parallel stop: Position the parallel
stop (9) flat on the edge of the workpiece and
start the cut.
6. Operation
6.1 Working with the mini hand-held circular
saw
•
Always hold the mini hand-held circular saw
firmly.
•
Do not use force!
Push forwards gently and evenly with the mini
hand-held circular saw.
•
The waste piece should be on the left-hand
side of the mini hand-held circular saw so that
the wide section of the support bench sup-
ports its full area.
•
If you are sawing down a line that has been
drawn, guide the mini hand-held circular saw
along the corresponding notch.
•
Clamp small pieces of wood securely before
sawing them. Never hold them with your
hand.
•
Always follow the safety instructions. Wear
safety goggles.
•
Do not use defective saw blades or blades
that are cracked or broken.
•
Do not use any flanges / flange nuts whose
bore hole is larger or smaller than those in the
Anl_TC_CS_860_1_Kit_SPK7.indb 20 Anl_TC_CS_860_1_Kit_SPK7.indb 20
GB
saw blade.
•
The saw blade must not be decelerated by
hand or by applying lateral pressure to the
blade.
•
The soleplate must not jam and must return
to its initial position after the operation has
been completed.
•
Before you use the mini hand-held circular
saw, check the function of the soleplate with
the mains plug disconnected.
•
Before you use the machine, ensure that the
safety equipment such as the soleplate, flan-
ges and adjustment devices are in working
order and are correctly adjusted and secure.
•
You can connect a suitable dust extraction
system to the dust extraction adapter (11).
Ensure that the dust extraction system is sa-
fely and correctly connected.
Danger! Always pull out the power plug befo-
re doing any work on the circular saw!
6.2 Using the mini hand-held circular saw
•
Select a suitable blade for the material you
wish to saw.
•
Check the condition and sharpness of the
blade.
•
Set the cutting depth.
•
Pick up the tool and make sure that no air
vents are covered.
•
Switch on the tool and wait for a few seconds
for the blade to reach operating speed.
•
Press the locking button (3) and, applying a
little pressure, slowly lower the tool into the
workpiece.
•
Push the saw forwards through the workpie-
ce. Never cut backwards!
•
Exert only little pressure on the tool when cut-
ting.
•
The base plate must always lie flat on the
workpiece.
•
Before you start your sawing work on the
workpiece, you can raise the soleplate (6)
with the lever (5) as shown in Fig. 6. Starting
the sawing work is then easier when you want
to begin at the edge of a workpiece.
6.3 Switching ON/OFF (Fig. 1)
To switch on: Slide the ON/OFF switch (2) for-
wards and hold.
To switch off : Release the ON/OFF switch (2)
Notice!Carry out a trial cut in a piece of waste
wood
- 20 -
02.09.2016 08:31:55 02.09.2016 08:31:55