Télécharger Imprimer la page

HK Audio LUCAS NANO 608i Manuel page 13

Masquer les pouces Voir aussi pour LUCAS NANO 608i:

Publicité

Les langues disponibles

Les langues disponibles

7 Technical Specifi cations
LUCAS NANO 608i System
Total power output*
Frequency response +/- 3 dB
Active protective circuits
Inputs
Outputs
Special features
Enclosure
Optional accessories
Weight
NANO 608i Satellite
Max SPL peak**
Max SPL**
Frequency response +/- 3 dB
Woofer
HF driver
Horn directivity
Nominal impedance
Inputs
Pole Mount Adapter
Dimensions (WxHxD)
Weight
NANO 608i Subwoofer
Max SPL peak**
Max SPL**
Frequency response +/- 3 dB 43 Hz - 190 Hz
Bass woofer
Nominal impedance
Pole mount
Dimensions (WxHxD)
Weight
* measured according to EIA
** @10% THD, half space
460 W (300 W + 2 x 80 W) Class D
43 Hz – 20 kHz
MultiBand Limiter, Subsonic Filter,
Thermo Protection, Overload Protection
4 1/4" (6.3 mm) jack/XLR combo ports,
2 1/4" (6.3 mm) jacks, 2 RCA/3.5 mm mini
jack (stereo), Bluetooth audio streaming,
Link In (for Twin Stereo mode)
Speaker Out, Easy-Click, Rec Out,
Footswitch/Aux Send Out, Link Out (for
Twin Stereo mode)
8-channel mixer with built-in DSP preamp
and eff ects section, Bluetooth audio
streaming, Bluetooth remote control for
additional DSP functions via the LUCAS
NANO REMOTE app for Apple iPad
Coated polypropylene
S-Connect Pole LN (signal-routing
speaker pole), Stereo Stand Add-on,
Roller Bag (padded trolley), Desk/Wall
Mount, Link Cable
16.3 kg / 35.9 lbs.
124 dB (Single Satellite)
130 dB (Satellite Array)
119 dB (Single Satellite)
124 dB (Satellite Array)
190 Hz – 20 kHz
4,5"
1" HK Audio Multicell Transformer
90° x 60° (Single Satellite)
90° x +10/-45° (Satellite Array)
8 ohms (Single Satellite)
4 ohms (Satellite Array)
Speaker In, Easy-Click
3/8" thread
14.5 x 14.5 x 13.5 cm
1.2kg / 2.6 lbs.
123 dB
120 dB
10"
8 ohms
M33 for the (signal-routing) S-Connect
Pole LN, a speaker pole adapter sleeve
(M33 to M20) is included
35 x 49 x 47 cm
13.9 kg / 30.6 lbs.
General Technical Specifi cations
Peak current
3A / 220-240V AC • 6A / 100-120V AC
Current consumption
0.7A / 220-240 V AC • 1.5A / 100-120V AC
pursuant to EN 60065***
Inrush current
70 A at 120 V and 230 V
*** Current consumption (mains power) was measured at the internal amplifier's output at 1/8 power
by inputting a sine wave as specified in the EN60065 standard. This value represents the average
current drawn from the mains grid when operating the system with standard music signals.
Apple, the Apple logo and iPad are trademarks of Apple Inc., registered in
the U.S. and other countries. App Store is a service mark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Stamer Musikanlagen
GmbH is under license.
For USA:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance. This
transmitter meets both portable and mobile limits as demonstrated in the RF Exposure Analysis. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with FCC multi-transmitter product procedures.
For Canada:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
LUCAS NANO 608i 1.0
13

Publicité

loading